background image

CAUTION

YOUR POOL IS DESIGNED TO PROVIDE AN AMPLE SAFETY MARGIN
WHEN IT STANDS ON LEVEL GROUND.  FOR THIS PURPOSE A SLOPE 
IN EXCESS OF 2 INCHES IN ANY DIRECTION WALL TO WALL IS 
CONSIDERED OFF LEVEL  YOUR POOL  WARRANTY ONLY APPLIES TO
POOLS INSTALLED ON LEVEL GROUND AS DEFINED ABOVE.  

ONCE YOU HAVE STARTED TO FILL THE POOL, DO NOT TRY TO PULL      
THE LINER FORCEFULLY.  THE WEIGHT OF EVEN ONE INCH OF WATER  

WILL MAKE IT IMPOSSIBLE TO MOVE THE LINER WITHOUT DAMAGING IT.

16

LINER INSTALLATION

13

LINER

INCORRECT

CORRECT

POOL

LINER

AIR

SPACE

POOL

LINER

STANDARD OVERHANG LINER

1. Clear all sticks and sharp objects from an area near the pool, that is 

as large as the pool itself. Remove the liner from its carton and unfold 
and open the liner. Refold the liner so that it can easily be carried to 
the pool and unfold from the outside of the pool. Check the 
levelness of the sand in the pool and make sure that no sharp 
objects are still in the pool.

2. Place the liner into the pool while holding onto the top of the 

wall section of the liner. Overhang the top wall of the liner over 
the pool wall approximately 4” and hold it by temporarily placing 
the plastic edging over the liner and the wall. Continue in this 
manner around the entire pool.

3. Gently pull on the liner and use a soft bristle broom to remove as many 

wrinkles as possible on the bottom of the pool. Adjust the overhang of the 
liner as needed as you go trying to keep it as equal as possible around the pool.

4. Be sure that the seam of the liner where the wall meets the floor of the liner is evenly centered in the pool.

Start filling the pool slowly with water. Continue pulling gently and working the liner with a broom, and 
readjusting the overhang as necessary.

5. Some wrinkling of the liner may be evident and in no way affects the structural strength of your pool.

Once the water is filled to a point that the liner is pressed firmly against the wall install the 
thru-the-wall skimmer following its instructions. Then you can fill the entire pool as quickly as
desired. 

The excess liner material overhanging the wall can either be trimmed later when the pool is 

filled, or double folded now to the inside of the pool between the liner and the wall. Permanently install 
the plastic edging around the entire pool, not leaving any gaps.

VINYL LINER

TOP RAIL

PLASTIC EDGING

OUTSIDE VIEW

OF POOL WALL

POOL

WALL

EARTH

MOUND

Содержание oval 4ft pool





























Отзывы: