6
Version Comments
1.0 Pre-release Manual for Smart Balance Charger
2.0 New Manual for Smart Balance Charger
2.1 Added Charging connection Controller Battery
4
5. Operation Instructions
START
>
2
Seconds
1. Standby
After the charger is powered on, it will enter standby mode.
Connect the battery and the balance port. The charger will
automatically detect the connected battery type.
LIPO BAL-CHG 2S
10S
2A
2. Charging Current selection
After entering the main interface, you can press the “INC” and
“DEC” buttons to set the charging current value. Check that the
selected current does not exceed the battery specifications.
Then press the “START” button to confirm the set value.
If there is no action in 10 seconds the program will
automatically recommend a charging current according to the
number of cells and capacity. The 10 second countdown will be
displayed in the lower left corner of the current setting
interface. The settings buttons will reset the countdown timer.
3. Start charging
Press and hold the "START" button for 2 seconds to start the
charging program. When in charging mode, the “INC”, “DEC” and
“ENT” buttons are not available. Press the “ESC” to stop charging.
LIPO BAL-CHG 2S
10S
1A
LI2s 7a 8.4v
bal 005.47 00121
This charger can only charge LiPo-2S or
LiHV-4S
batteries.
DO NOT CHARGE ANY OTHER BATTERY TYPE AND NEVER LEAVE A
CHARGING BATTERY UNATTENDED.
5
6. Interface Description
Error messages:
CONNECT BREAK!
CELLS IMBALANCE!
OVERHEATING!
OVER CAPACITY!
POLARITY REVERSE
HIGH VOLTAGE!
HIGH CELL VOLT!
SHORT CIRCUIT!
POWER SUP FAULT!
SELF TEST FAULT!
CELLS ERROR!
SAFETY TIMER!
SETTINGS CHANGED
When the charger is used incorrectly or there is a fault, the charger will
prompt an error message for the user to view. As shown below:
type of battery
Balanced charging mode
Charging voltage
Charged capacity
LI2s 7a 8.4v
bal 005.47 00121
Charging current
Charging time
The battery has been disconnected from the charger.
The cells of the battery are unbalanced. The battery cannot be
charged.
The charger has overheated. Power off the charger and allow it
to cool.
The connected battery cannot be charged.
The battery has been incorrectly connected. Check all
connections.
The input voltage is too high. The battery cannot be charged.
The battery voltage is too high. The battery cannot be charged
.
The connected battery has an incompatible number of cells.
The connected battery has not charged in a safe time.
The selected setting has been changed successfully.
The charger output has been short-circuited.
The input supply is unacceptable.
The charger`s self-test has failed. The charger cannot be used.
7. Specifications
130*115*61mm
380g
2-10A
5W
LiPo-2S
、
LiHV-4S
AC input 100-240V DC output 11V-18V
Input
Output Power
Battery types
Charging Current
Discharge power
Battery Numbers
Balance Current
Input Protection
Output Protection
Working Temperature
Size
Weight
LiPo
、
LiHV
400mA/cell
Overcurrent
Overvoltage, undervoltage, short circuit, overheating,
short circuit, reverse connection
5-45
℃
100W
Note: The product specifications mentioned in this manual are for
reference only. This manual is correct at the time of release, and is subject
to change without notice.
7
8. After-sales and Warranty
9.Warning
10.Version Information
Thank you for purchasing this SwellPro product, we will do our best to
provide you with comprehensive after-sales service to fully protect your
rights. If your product is at fault, please contact SwellPro after-sales staff.
1. The product is covered by a 12-month warranty.
2. Warranty repairs are free of charge for one year from the date of
purchase.If the customer is unable to provide valid proof of purchase, the
date will be based on the internal date code of the charger.
3. For repairs after the first 12 months of use, the cost will be charged as
appropriate, and the customer shall bear the round-trip shipping costs.
1. Product damage caused by failure to use a suitable input voltage as required.
2. Damage caused by not following the instructions.
3. Any man-made, accidental impact or other force majeure that causes damage
to the product.
4. Modification, disassembly or modification of the internal circuit of this product
without the approval of the company.
5. Water immersion or intrusion, moisture or other foreign matter entering the
product and causing damage.
6. Aging, bumps and scratches on the surface of the product.
The product specifications and information mentioned in this
manual are for reference only and are subject to change without
notice.
Warranty does not cover damage due to neglect or incorrect usage of the
charger including:
The user is responsible for any consequences caused by the operation of
the charger. SwellPro is not liable for the costs beyond the cost of the
product and reserves the right to modify the terms of this warranty which
is subject to change without notice.
●
1. This product is not intended for use by persons with physical, sensory or
mental disabilities or lack of experience and relevant knowledge (especially
children).
●
2. This product is not a toy. Please keep away from children.
●
3. If the product is in any way damaged, turn off the power to avoid the risk
of electric shock.
●
4. This product is for indoor use only.
