Swegon BlueBox Kappa Sky Скачать руководство пользователя страница 36

Страница: 36 / 76

We reserve the right to make changes without any prior notice.

Translation from original instructions

Fig. 8 Recommended hydraulic circuit

Evaporator

Water filter

Thermometer

Motor-driven pump

Flow switch

Flexible coupling

System filling unit

Water pressure gauge

Valve

Safety valve

Storage tank

Air valve

Expansion vessel

Check valve

It is essential for the water to come in at the connection indicated in the dimensional diagram and with the

relevant label on the unit.

If it does not, there would be a risk of the evaporator being frozen since the antifreeze probe control would be thwarted.

The hydraulic circuit must be made in such a way as to ensure a constant flow of water to the exchanger in all operating

conditions.

If this is not done, there will be a risk of refrigerant returning to the liquid state at the compressor inlet, with the danger of it

breaking.

Operation with a variable water flow rate at the user-side exchanger is allowed only if the inverter pump is integrated in the

unit (and therefore supplied by the manufacturer) and if the hydraulic circuit is made in accordance with the manufacturer's

specific instructions.

Содержание BlueBox Kappa Sky













































































Результаты поиска

Содержание BlueBox Kappa Sky

Отзывы:

Похожие инструкции для BlueBox Kappa Sky

Бренды по названию

Популярные бренды

Swegon BlueBox Kappa Sky, Инструкция по установке, использованию и техническому обслуживанию

Результаты поиска

Содержание BlueBox Kappa Sky

Отзывы:

Похожие инструкции для BlueBox Kappa Sky

Бренды по названию

Популярные бренды