background image

InstructIon booklet

6

InstructIon booklet

InstructIons for use

adjustable PosItIve dePtH stoP

The adjustable depth stop is threaded into the base of the saw at the rear. By raising and lowering the depth stop bolt 
with a wrench you can control how far the abrasive wheel travels when the saw handle is depressed.

Power suPPly

Before operating the cut-off saw, check the power supply and make sure it meets the requirements listed on the 
nameplate. A substantial voltage drop will cause loss of power and the saw to overheat.

Common causes of power loss and saw overheating include insufficient extension cord size and multiple tools 
operating from the same power source.

swItcH

To start the tool, completely depress the trigger and safety switches located in the saw handle.

To stop the tool, release the trigger switch completely.

cuttInG

Warning. Do not attempt to cut wood or masonry with this saw. Never cut magnesium or magnesium alloy with this 
tool. Failure to comply with this warning could result in serious injury.

1.  Secure the tool in place to prevent saw movement or tipping during the cutting procedure.
2.  Firmly secure the material to be cut using the saws’ vise.

Warning. Large, circular or irregularly shaped material may require additional means of clamping to be 
secured in place for cutting. Use C clamps and blocks to hold material securely. Failure to comply could 
result in serious injury.

3.  Start the saw by fully depressing the trigger switches and allow the cut-off wheel to come up to full speed before  
 

contacting wheel to material.

4.  Slowly push down the saw arm handle until the cut-off wheel contacts the material being cut. Use a steady and   
 

even amount of pressure to obtain a uniform cut. Never force the wheel into the material.

5.  When the cut is complete, release the trigger switch and allow the wheel to stop before raising it to the full  
 

open position.

Danger. Do not touch the cut material until it cools or you will be burned. Failure to heed this warning will 
result in serious personal injury.

 

Содержание 355MM













Отзывы: