swaploader SL-400 Скачать руководство пользователя | Manualshive

Страница: 70 / 136

background image

10/05/09

FENDER ASSEMBLY, SINGLE AXLE

Aluminum (10H93) / Steel (11H13)

INSTALLATION INSTRUCTIONS (continued)

4. Mark mounting holes through the fender bracket weldment onto the fender. Remove

the bracket and drill 7/16” dia. Holes in fender (See FIG. 3).

5. Attach fender bracket weldments to fender using fasteners provided.

MATERIAL LIST

ITE

M

QTY P/N

DESCRIPTION

WT lb.

PER EA.

1 4 10H74

FENDER

BRACKET

WDMT.

8.05

2 4 21H37

MOUNTING

PLATE

1.09

3 4 21H42

RUBBER

SPACER

.85

4 4 21H61

FENDER

TUBE

1.26

5

32

00P34

3/8-16 UNC LOCKING NUT

.02

6

48

00771

3/8 DIA. FLAT WASHER

.05

7

16

00P78

3/8 DIA. NYLON WASHER

-

8

16

00P44

3/8-16 UNC X 1-1/2 HHCS

.07

9

16

01P21

3/8-16 UNC X 2-1/2 HHCS

.09

10 2

FENDER

90P24

FENDER

–

ALUMINUM

19.00

90P25

FENDER

–

STEEL

35.00

ALUMINUM FENDER TOTAL

87.80

STEEL FENDER TOTAL

119.80

1

4 @ 6”

CENTERS

7/16 DIA. HOLE

HOIST
MAINFRAME
(REF)

TRUCK
(REF)

ADDITIONAL NOTES:

Prior to any welding, consult the
truck manufacture for any special
precautions that may need to be
taken. Typically the batteries must
be disconnected and the ground
lead from the welder should be as
close to the part being welded to
avoid the possibility of arcing across
bearings, gears, etc.

6. Weld mounting plates [Part No. 21H37] to

fender tubes [Part No. 21H61].

7. Position fender tubes with mount plates on

hoist mainframe; align with fender
bracket weldments. (NOTE: Fender tube
length may need to be modified to fit
specific application.)

8. Weld fender tube to hoist mainframe. If

attaching the fender tubes to the truck
chassis, an additional mount plate may
need to be fabricated so the assembly
can be bolted to the to the truck chassis.

9. Attach fender bracket weldment [Part No.

10H74] to mounting plate [Part No.
21H37] using fasteners provided
(See FIG. 3).

5

6

2

4

3

10

7

6

9

8

6

5

1800 NE Broadway Avenue, Des Moines, Iowa, U.S.A. 50313-2644

Phone: (515) 266-3042

•

Fax: (515) 313-4426

•

Toll Free: (888) 767-8000

E-Mail: [email protected]

•

Web Site: www.swaploader.com

«
...
68
69
70
71
72
...
»

Содержание SL-400









































































































































Отзывы:

Нет отзывов

Похожие инструкции для SL-400

Бренд: AUSA Страницы: 72

Бренд: U-Line Страницы: 15

Бренд: DAF Страницы: 74

Бренд: Magliner Страницы: 7

Бренд: unicraft Страницы: 50

Бренд: Paccar Страницы: 239

Wireless Remote Control Wheel V3

Бренд: OPTITEC Страницы: 11

Бренд: MONDELIN Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды