How to Use
Before first use
Remove any stickers, protective foil or storage cover from the
soleplate.
Heat up the iron to maximum temperature and iron over a piece
of damp cloth for several minutes for the purpose of removing any
residue on the soleplate.
Note:
It is normal for a slight odour to come from the unit during
the first use. This is due to light oils used to preserve components
during manufacture. The odour will disappear after first use.
Operation
1. Press both Handle Release Buttons at the same time and put
the handle down (fig 1). Connect the power cord to outlet, the
power light illuminates.
2. Press the tank lock button then take out water tank from stand.
Remove the limescale filter. Fill the tank but do not exceed the
MAX level indication on the side (fig 2 - 6).
3. Replace the limescale filter and slide the tank back into the iron
base, making sure it “clicks” into place. Check the garment label
for the required ironing temperature. Then turn the temperature
dial to your desired setting. And the heating light will be illuminated.
Tips: to prevent shiny spots, iron the reverse side of the fabric
for silk, wool and synthetic materials; and to prevent stains, avoid
using the steam functions (put Steam ON/OFF switch in OFF
position).
Once the soleplate temperature has reached the preset
temperature, the heating light will go out, press down Steam
Button. The pump will start and after a few seconds the steam
will come through. Please note when pressing the steam button
for the first time at the start of the new ironing session, direct the
iron away from garments to allow any small amounts of water from
previous ironing sessions to be ejected.
NOTE: THE PUMP MAY MAKE A NOISE FOR A FEW SECONDS
UNTIL IT IS PROPERLY PRIMED. YOU CAN PRIME THE PUMP
A LITTLE QUICKER IF YOU HOLD THE HAND UNIT BELOW
THE HEIGHT OF THE BASE - GRAVITY WILL GET THE STEAM
THROUGH QUICKER!
Tip: the interconnection cord can become quite hot after extended
use, do not touch! At any time during the ironing session, you can
place the iron on the silicone cushion or on the heel rest (and have
a nice cup of tea). Note: the steam output is 60-90g/min
Always check first whether a label with ironing instructions is attached to the article.
The iron heats up quicker than it cools down, therefore, you should start ironing the
articles requiring the lowest temperature such as those made of synthetic fibres.
If the fabric consists of various kinds of fibres, you must always select the lowest ironing
temperature to iron the composition of those fibres.
Silk and other fabrics that are likely to become shiny should be ironed on the inner side.
Velvet and other textures that rapidly become shiny should be ironed in one direction
with light pressure applied. Always keep the iron moving at any given moment.
Pure woollen fabrics (100% wool) may be ironed with the iron set a steam position.
Preferably set steam button to the maximum position and use a dry cloth as a mat.
Note
: when ironing woolen fabrics, shining of the fabric may occur. So it is suggested
that you should turn the article inside out and iron the reverse side.
Ironing Tips
Cleaning and Maintainance
AFTER IRONING
1. Take out the water tank, remove the limescale filter and empty all the water out, replace the filter
then place tank back into the iron base (fig 2 - 6).
2. With the tank empty, press down the steam surge button button a couple of times to remove any
remaining water in the interconnecting cord, then place the iron back on the base. Warning: the
soleplate is still hot, be careful!
3. Turn the temperature dial back to 0 position and unplug from the mains socket. Allow the iron to
completely cool before cleaning. Note: you can wipe the surface of unit clean with a soft cloth. Try
not to dislodge the silicone cushion out of it’s mountings because it is difficult to fit back!
Warning: do not immerse the steam iron or stand in water or other liquids.
AUTO-DESCALING FEATURE
There is a limescale filter inside the tank. The filter can absorb insoluble calcium ions and convert
them to soluble natrium ions, which makes the water softer. This greatly reduces the build-up of
limescale. However, if you do live in a hard water area, the life of your iron will increase significantly
if you use bottled water.
Note: to keep the soleplate smooth, never let any metal materials rub against it.
REPLACE THE LIMESCALE FILTER EVERY 3 MONTHS OR MORE REGULARLY IF YOU LIVE
IN A HARD WATER AREA.
VISIT WWW.SWAN-BRAND.CO.UK
FOR SPARE FILTERS
wan
designed for life
wan
designed for life
Helpline Number: 0121 327 6889
WWW.SWAN-BRAND.CO.UK
Helpline Number:
0121 327 6889
WWW.SWAN-BRAND.CO.UK
use vertical steam for garments
SI9020N.indd 6-7
20/06/2012 09:25
