1)
Connect both the Camera and the Receiver to their respective power adaptors.
2)
Connect the Receiver to the AV input of the equipment you wish to view the camera on (Security
Monitor, TV, VCR etc) using the supplied AV to RCA cable. These sockets are marked Video IN or AV IN
and are usually yellow in color.
Change your Security Monitor, TV or VCR to the AV input channel. There are various methods for doing
this that vary from one type to another. If you have an
AV TV
with RCA sockets you will need to switch
the
TV
to the
AV
channel to view the camera. To connect the receiver to your
VCR
, you will need to
turn the
VCR
to the
AV Input
selection and turn your
TV
onto the channel you would normally use
to view a tape or movie on your
VCR
. The AV channel on your TV or VCR may be activated by a
button on your remote that is marked with this symbo ,
L
1
or
L2
or possibly
AV
1
or
AV2
. Please
consult the manual of your particular TV or VCR for further information on using their AV inputs. Make
sure the antenna is correctly positioned, check the image for clarity and make minor adjustments to
obtain the best picture.
obtain the best picture
Press the
SEL
button on the receiver until the LED for your cameras
are lit. If the channel LEDs flash
and the receiver scans through all 4 channels, move the Loop mode dip switch
L
on the back of the
receiver up into the OFF position.
3)
In some cases to
you will also need to adjust the
position of the Camera and Receiver to suit your particular situation. Try slightly different locations for
either unit to achieve optimal results.
4)
Camera with Stand
Small Plug Power Adaptor (8V)
Poor Picture:
Realign antennas until image quality improves, slightly adjust the position of the Night Hawk Camera or
Receiver. Change the location of the Camera, or use a different Camera in the location experiencing interference that is on a
different channel. In some cases interference may be caused by another device on a similar frequency to the channel you
are using. Change to one of the other channels and check the signal quality again.
Lines only - no clear picture:
Check to confirm there is no microwave oven or other 2.4GHz equipment operating
close by ie; Cordless Telephones, Wireless Baby Monitors, Wireless LAN equipment etc.
Make sure the Receiver is on the
correct channel for the particular camera.
Picture ghosting or interference:
Some home appliances such as Wireless LANs, 2.4GHz portable telephones and
Microwave ovens operate on or near the 2.4GHz frequency. If you receive interference from such an appliance, try moving
the Camera or Receiver to location further away from the appliance or in the event of interference from a Wireless LAN
device,
try changing the Wireless LAN to a different channel to improve the signal quality.
No picture
:
check the receiver to confirm it is turned ON and make sure the A/V connection of the Receiver is not
plugged into the Audio Out socket. Make sure the Receiver is on the correct channel. Check that the channel on the
receiver is the set to the same as the camera you wish to view. Check to ensure the camera is plugged in and has power
(cup your hands around the camera and you should see a faint red glow from the IR LEDs). You can use the infrared lighting
facility to pick up a picture inside a dark environment. If your monitor does not display a picture in a dark environment,
check the camera to be certain that infrared lighting is within range of the subject. Try to move the item within the 2-3m (6-
9ft) range of the Cameras IR LEDs or place the Camera nearer to the object until a clear picture is displayed on the
Monitor.
FCC Notice
We, Swann Communications of 10612 Shoemaker Avenue, Bldg A, Santa Fe Springs, CA 90670 USA, declare
under our sole responsibility that the product:
SW-P-WOC2
This product meets the requirements specified in Part 15 of FCC Regulation. Operation rests with the following
two conditions:
(1) The equipment should not cause any harmful interference;
(2) The equipment must receive and process any interference, including any possible interference caused by
operation mistakes. After testing the product, we confirm that it complies with the provision for class C digital
equipment in the 15th part in FCC regulation; and the receiver complies with the limitations for class B digital
equipment in Part 15 of FCC regulation. The product generates, applies and emits radio waves. It might cause
harmful interferences to wireless communication if not be installed and used following the description of the
manual. The product may cause interference in residential area, and the customer should take remedies to
eliminate the interference at their own costs. If the product causes any harmful interference to wireless
equipment or disturbs the receiving of TV signals (it can be identified by turning on and off the product), you
can solve the trouble by following methods:
(1) Re-adjust the product or put it in another place;
(2) Extend the distance between the equipment interfered and the product; and
(3) Refer to dealers or experienced radio electrician for help.
CE Notice
This product complies with standards including
L
ow
V
oltage
D
evice Directive 73/23/EEC;
EMC
Directive 89/336/EEC and
R&TTE
Directive 1999/5/EC. It passed the subject tests by the authority concerned and is authorized to bear
CE
mark.
6
3
Troubleshooting, Hints and Tips
Setting Up Your System
Receiver
External antenna
Audio / Video Out
To Audio and
Video IN
Monitor or TV
DC 8V Socket
Channel
Selector
Button
Loop On/Off Dip Switch
Active
Channel
Leds
Receiver
Power Adaptor
Disable Channel 1,2,3,4 Dip Switches