Swallow Boats BayRaider Скачать руководство пользователя | Manualshive

Страница: 11 / 22

background image

Photo 2. The head of the jib (1) is shackled to the top swivel (2) which is shackled to the
jib halyard (4).

Photo 3. The rope strop (1) should be regularly inspected for wear. Note how the strop is
folded over the boom, thus theoretically multiplying the ropes breaking load by 4.

«
...
9
10
11
12
13
...
»

Содержание BayRaider























Отзывы:

Нет отзывов

Похожие инструкции для BayRaider

Бренд: Nacra Страницы: 40

Бренд: Velocity Страницы: 18

Бренд: Sea Pro Страницы: 50

Бренд: SeaDoo Страницы: 39

Бренд: Sea-doo Страницы: 15

Бренд: Sea Ray Boats Страницы: 26

Бренд: Sea Eagle Boats Страницы: 8

Бренд: Sea Eagle Страницы: 13

Бренд: Sea Ray Страницы: 80

Бренд: Sea-doo Страницы: 202

Бренд: Sea-doo Страницы: 314

Бренд: Grady-White Boats Страницы: 62

Бренд: Grady-White Boats Страницы: 68

Бренд: Grady-White Boats Страницы: 123

Бренд: XO boats Страницы: 58

Бренд: Boston Whaler Страницы: 82

Бренд: LaserPerformance Страницы: 10

Бренд: LaserPerformance Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды