background image

 

SW-Stahl und Werkzeugvertriebs GmbH 

Tel. +49 (0) 2191 / 46438-0 

www.swstahl.de 

Leverkuser Straße 65 

Fax +49 (0) 2191 / 46438-40 

D-42897 Remscheid 

E-Mail: [email protected] 

 

LAMP INDICATIONS 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
                        - 9 - 

Red Lit 
Charger is plugged into the AC outlet. Ready to charge. 
 
Yellow Flashing 

(1) When the temperature of the battery is too low (<0

o

C (<32

o

F)), it 

is  in  a  trickle  charge  mode  until  the  temperature  of  the  battery 
goes  up  to  over  0

o

C  (<32

o

F).  The  lamp  will  change  from  the 

Yellow  Flashing  to  Green  Flashing  automatically  and  start  to 
charge.  (If  after  70  minutes,  the  lamp  changes  from  yellow 
flashing to yellow lit, consult an authorized dealer.) 

(2) When the temperature of the battery is too high (>40

o

C (104

o

F)), 

it is in a trickle charge mode until the temperature of the battery 
drops  to  under  40

o

C  (104

o

F).  The  lamp  will  change  from  the 

Yellow  Flashing  to  Green  Flashing  automatically  and  start  to 
charge.  (If  after  70  minutes,  the  lamp  changes  from  yellow 
flashing to yellow lit, consult an authorized dealer.) 

(3) When  the  voltage  of  the  battery  is  too  low  (below  10.8  voltage 

for 14.4V tools), it is in a trickle charge mode until the voltage of 
the battery reaches to the standard value. The lamp will change 
from  the  Yellow  Flashing  to  Green  Flashing  automatically  and 
start  to  charge.  (If  after  20  minutes,  the  lamp  changes  from 
yellow flashing to yellow lit, consult an authorized dealer.) 

 

 

 
Yellow Lit 
The battery and the charger are not connected. If the yellow lit 
still on after trying re-attach the battery, consul the an 
authorized dealer. 
 
Green Flashing 
Now start charging 
 
Green Flashing 
Battery is approximately 50% charged. 
 
Green Flashing 
Battery is approximately 80% charged. 
 
Green Lit 
Charging is complete. (Fully charged.)

 

Содержание S3201













Отзывы: