manualshive.com logo in svg

Svpribor Irk-Pro gamma, Инструкция по эксплуатации

Поделиться
Скачать
Svpribor Irk-Pro gamma Скачать руководство пользователя страница 11

11

TRACE VIEWING

Linear scale

There are two cursors on the TDR screen, between them the distance is measured on the trace. 
To make a cursor an active – press the 

◄►

 keys. To vertical move a trace – press the 

▲▼

 

key.

To operate with the trace gauges use the following keys: [PULSE], [RANGE], 
[AMPLIFICATION]. At setting the viewing range the device select itself the measuring pulse 
width. The [STRETCHING] key is used to view the detail trace around an active cursor. The 
[MAP] key is used to view the whole cable. The [AVERAGING] key is used to eliminate the 
occasional noises and to rice picture stability during the averaging increasing.
The keys on the left vertical part of the menu are changing the TDR working mode: trace 
recording [trace memory], activation of the logged trace for the comparison [+ memory]; work 
in separate or combined mode; adjusted pulse amplitude, the mode of averaging for a line with 
intensive noise.

The keys on the left vertical part of the menu:

Trace recording [trace memory]; 
activation of the logged trace for the comparison [+ memory];
work in separate or combined mode;
selection of the match resistance;
selection of the scale (linear, logarithmic, pseudologarithmic)

š

š

š

š

š

Содержание Irk-Pro gamma











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды