two blinking stripes will illuminateon the display of the subwoofer. Press it again, and the speaker
system will return to operation mode.
Audio Source Selection
•
There are two stereo inputs (
DŽDž
, AUX) and 5.1CH input in the Home Theatre Speaker System.
To listen to a stereo audio source, connect it to AUDIO INPUT (
k
, Fig. 2) of the speaker system, as
shown in Fig. 5. To listen to a multichannel sound source, connect its multichannel output to 5.1CH
INPUT (
l
, Fig. 2) of the speaker system (see connection diagram, Fig. 5). Depending on the required
connection, select the desired audio source with the INPUT button on the control panel of the
subwoofer (
d
, Fig. 1) or with the DVD
b
, PC
c
or AUX
d
buttons (Fig. 3) on the remote control.
The subwoofer display will illuminate with a corresponding inscription.
Turning on and Setting the Tuner
•
Press the SCAN
q
and FM/AM
s
buttons on the remote control to turn on the tuner and select
the FM or AM band.
• Manual setting.
Press the TUNE + or TUNE- buttons
r
on the remote control for
ԛ
ne-tuning the
frequency of the radio station.
• Auto search.
By holding SCAN
q
on the remote control for more than 1 second, turn on the
scanning of the FM band starting with 87 MHz frequency, the found radio stations being memorized
sequentially: «CH 01», «CH 02», «CH 03», etc. Scanning of the FM band will continue until 108 MHz
frequency. After the scanning, the
ԛ
rst found radio station turns on.
•
Additionally, you can turn on the desired broadcast quickly with the numeric keypad buttons (
h
and
i
) on the remote control, having saved systems of 20 FM radio stations and 20 AM radio
stations.To save the found radio station, press MEMORY
t
on the remote control (CH _ _ will
illuminate on the display), then enter its number (from 0 to 19) with the numeric keypad buttons (
h
and
i
) on the remote control, which will illuminate on the display (for example, CH 09). After
saving the required quantity of radio stations, enter the number of your desired radio station on the
remote control with the numerical keypad buttons (
h
and
i
) for quick search.
Master Volume Control
•
Press VOL+ or VOL– (
m
, Fig. 3) on the remote control or turn the VOLUME knob (
b
, Fig. 1) on the
front panel of the subwoofer to adjust (increase/decrease) the volume level.
Satellites and Subwoofer Volume Control
•
The volume level of the front, rear and center channel satellites can be adjusted with FRONT+/-
f
,
S/-
e
and CEN+/-
n
on the remote control. While SUB+/–
o
on the remote control or
SUB+
g
and SUB–
h
on the control panel of the subwoofer (see Fig. 1) can adjust the subwoofer
volume level.
2D/3D sound
•
To select between 2D and 3D sound modes, press the 2.1/5.1 button (
l
, Fig. 3) on the remote
control or the subwoofer control panel (
e
, Fig. 1), while your audio source is on. 3D or 2D mode
inscription will illuminate on the display according to the selected mode. If 5.1 audio source (DVD)
is connected and on, this feature is unavailable.
Mute feature
•
Press MUTE
j
on remote control or button MUTE
f
on control panel of subwoofer to tempo-
rarily turn o
Ԛ
the sound. Press this button again to turn on the sound.
Note. If the speaker system is left unused for a long time, mind to switch off the device by
using POWER On/Off switch and unplug it.
ENG
9
Operation Manual
BTR5-10
