manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

8B-74 Air Bag System: 

NOTE:
Upon completion of inspection and repair work, perform the following items.
• Reconnect all air bag system components, ensure all components are properly mounted.
• Clear DTCs referring to “DTC Clearance: ”, if any.
• Repeat “Air Bag Diagnostic System Check: ” to confirm that the trouble has been corrected.

 

3

1) With ignition switch OFF, disconnect special tools (B) 

and (C) then reconnect connector “L25” or “L30”.

2) Disconnect side-air bag (inflator) module connector (1) 

from side-air bag (inflator) module.

3) Check proper connection to side-air bag (inflator) 

module at terminal in connector.

4) If OK, then connect special tools (A), (B) and (C) to side-

air bag (inflator) connector.

Special tool
(A):  09932–76010
(B):  09932–75010
(C):  09932–78310

5) Check SDM DTC.

With ignition switch ON, is DTC B1061 or B1065 still 
indicated?

DTC B1061: Repair 
high resistance or open 
in “WHT/RED” or “WHT/
GRN” wire circuit in seat 
harness.
DTC B1065: Repair 
high resistance or open 
in “GRY/BLU” or “LT 
GRN/RED” wire circuit 
in seat harness.

Replace side-air bag 
(inflator) module 
referring to “Side-Air 
Bag (Inflator) Module 
Removal and 
Installation: ”.

Step

Action

Yes

No

1

“L25”, “L30”

STEERING WHEEL

(B)

(C)

(A)

I4RS0A820034-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

AC Schnitzer F40 Fitting Instructions Manual preview
F40
Бренд: AC Schnitzer Страницы: 16
DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Бренд: DANA Страницы: 42
dallara F305 Manual preview
F305
Бренд: dallara Страницы: 37
Yakima BOA Installation Instructions Manual preview
BOA
Бренд: Yakima Страницы: 8
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Бренд: Jeep Страницы: 6
Chevrolet Camaro 12000 1968 Series Factory Assembly Instruction Manual preview
Camaro 12000 1968 Series
Бренд: Chevrolet Страницы: 455
Actia TGU-R ACCESS User Manual preview
TGU-R ACCESS
Бренд: Actia Страницы: 37
STC 552-010 Installation Instructions Manual preview
552-010
Бренд: STC Страницы: 6
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Бренд: Ford Страницы: 368
Draw tite 24943 Installation Instructions preview
24943
Бренд: Draw tite Страницы: 4
Mercedes-Benz CLS 280 2008 Owner'S Manual preview
CLS 280 2008
Бренд: Mercedes-Benz Страницы: 329
Icom RMK-5 Instruction Manual preview
RMK-5
Бренд: Icom Страницы: 20
Dodge 2005 JR41 Stratus Owner'S Manual preview
2005 JR41 Stratus
Бренд: Dodge Страницы: 293
Elinchrom ELB 1200 User Manual preview
ELB 1200
Бренд: Elinchrom Страницы: 101
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Бренд: Mazda Страницы: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Бренд: Toyota Страницы: 50
Xpresskit PKTX Installation Manual preview
PKTX
Бренд: Xpresskit Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды