manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-25

TORQUE REDUCTION SIGNAL

ON: Signal which TCM require ECM to reduce output 
torque at shifting gear
OFF: Signal which TCM does not require ECM to reduce 
output torque

ENGINE COOLANT TEMPERATURE (

q

C, 

q

F)

Engine coolant temperature computed by duty signal 
from ECM.

AIR CONDITIONER SIGNAL

ON: Signal which inform that air conditioner compressor 
is turned ON.
OFF: Signal which inform that air conditioner 
compressor is not turned ON.

ENGINE TORQUE SIGNAL (N

˜

m)

Engine torque computed by duty pulse signal outputted 
from ECM.

SLIP RPM (RPM)

This parameter indicates slipping rotation in the torque 
converter (difference between input shaft rotation and 
engine rotation)

MIL REQUEST

ON: Signal which TCM requires combination meter to 
turn on malfunction indicator lamp.
OFF: Signal which TCM does not require combination 
meter to turn on malfunction indicator lamp.

FUEL CUT FLAG

ON: Signal which inform that fuel cut is operating.
OFF: Signal which inform that fuel cut is not operating.

A/T Basic Check

S4RS0A5104010

This check is important for troubleshooting when TCM has detected no DTC and no abnormality has been noted in 
“Visual Inspection: ”. Follow the flow carefully.

Step

Action

Yes

No

1

Was “A/T System Check” preformed?

Go to Step 2.

Go to “A/T System 
Check: ”.

2

Perform “Road Test”.

Is it OK?

Go to Step 3.

Proceed to 
“Troubleshooting” in 
“Road Test: ”.

3

Perform “Manual Road Test”.

Is it OK?

Go to Step 4.

Proceed to 
“Troubleshooting” in 
“Manual Road Test: ”.

4

Perform “Engine Brake Test”.

Is it OK?

Go to Step 5.

Proceed to 
“Troubleshooting” in 
“Engine Brake Test: ”.

5

Perform “Stall Test”.

Is it OK?

Go to Step 6.

Proceed to 
“Troubleshooting” in 
“Stall Test: ”.

6

Perform “Time Lag Test”.

Is it OK?

Go to Step 7.

Proceed to 
“Troubleshooting” in 
“Time Lag Test: ”.

7

Perform “Line Pressure Test”.

Is it OK?

Go to Step 8.

Proceed to 
“Troubleshooting” in 
“Line Pressure Test: ”.

8

Proceed to “Trouble Diagnosis 1” in “A/T Symptom 
Diagnosis: ”.

Is trouble identified?

Repair or replace faulty 
parts.

Go to Step 9.

9

Proceed to “Trouble Diagnosis 2” in “A/T Symptom 
Diagnosis: ”.

Is trouble identified?

Repair or replace faulty 
parts.

Proceed to “Trouble 
Diagnosis 3” in “A/T 
Symptom Diagnosis: ”.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

JASTEC von-S2 Instruction Manual preview
von-S2
Бренд: JASTEC Страницы: 12
Jetter JX3-BN-CAN Manual preview
JX3-BN-CAN
Бренд: Jetter Страницы: 4
K&K M5700N Manual preview
M5700N
Бренд: K&K Страницы: 8
K&K M4700 Manual preview
M4700
Бренд: K&K Страницы: 20
K&K M3500N Manual preview
M3500N
Бренд: K&K Страницы: 6
K&K M2500 Manual preview
M2500
Бренд: K&K Страницы: 3
K&K M1500 Manual preview
M1500
Бренд: K&K Страницы: 3
Jeep 2011 grand cherokee Accessories Quick Reference Manual preview
2011 grand cherokee
Бренд: Jeep Страницы: 22
Jeep 2013 Grand Cherokee Owner'S Manual preview
2013 Grand Cherokee
Бренд: Jeep Страницы: 704
Jeep 2012 Liberty Owner'S Manual preview
2012 Liberty
Бренд: Jeep Страницы: 558
Aries P35-2004 Installation Manual preview
P35-2004
Бренд: Aries Страницы: 3
Motoalliance VIPER MA11922 Install Instructions Manual preview
VIPER MA11922
Бренд: Motoalliance Страницы: 8
Fabbri BICI OK 2 Manual preview
BICI OK 2
Бренд: Fabbri Страницы: 32
Whelen Engineering Company SAK34 Installation Manual preview
SAK34
Бренд: Whelen Engineering Company Страницы: 2
Quadratec QRC Installation Manual preview
QRC
Бренд: Quadratec Страницы: 8
Curtis 1POLXP1000GS Installation & Owner'S Manual preview
1POLXP1000GS
Бренд: Curtis Страницы: 5
Jeep WG Grand Cherokee 2002 Service Manual preview
WG Grand Cherokee 2002
Бренд: Jeep Страницы: 74
GStop GSTOP LITE Manual preview
GSTOP LITE
Бренд: GStop Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды