manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Fuel System:  1G-8

Installation

1) Install clamps to marked location on pipes. If clamp 

is deformed, its claw is bent or broken, replace it with 
new one.

2) Install pipes with pipe clamps to vehicle.
3) Connect fuel hoses and pipes to each pipe referring 

to “Fuel Hose Disconnecting and Reconnecting: ”.

4) Connect negative cable at battery.
5) With engine OFF, turn ignition switch to ON position 

and check for fuel leaks.

Fuel Injector On-Vehicle Inspection

S4RS0A1706006

1) Using sound scope (1) or such, check operating 

sound of injector (2) when engine is running or 
cranking.
Cycle of operating sound should vary according to 
engine speed.
If no sound or an unusual sound is heard, check 
injector circuit (wire or coupler) or injector.

2) Disconnect connector (1) from injector, connect 

ohmmeter between terminals of injector and check 
resistance.
If resistance is out of specification, replace.

Resistance of fuel injector
11.3 – 13.8 

:

 at 20 

q

C, 68 

q

F

3) Connect connector to injector securely.

Fuel Injector Removal and Installation

S4RS0A1706007

WARNING:

Before starting the following procedure, be 
sure to observe “Precautions on Fuel System 
Service: ” in order to reduce the risk or fire 
and personal injury.

 

Removal

1) Relieve fuel pressure according to “Fuel Pressure 

Relief Procedure: ”.

2) Disconnect negative cable at battery.
3) Disconnect MAF sensor connector, and detach 

EVAP canister purge valve.

4) Remove air cleaner assembly with air intake pipe.
5) Disconnect fuel injector couplers.
6) Disconnect fuel feed hose from fuel delivery pipe (1).
7) Remove fuel delivery pipe bolts (2).
8) Remove fuel injector(s) (3).

I2RH0B170007-

I2RH0B170008-

2

1

3

3

I3RM0A170010-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Camcar 2155 Fitting Instructions preview
2155
Бренд: Camcar Страницы: 2
Front Runner Easy-Out Fitting Instructions preview
Easy-Out
Бренд: Front Runner Страницы: 5
CARRYBOY CB-796IG2-CIGD-R Installation Manual preview
CB-796IG2-CIGD-R
Бренд: CARRYBOY Страницы: 4
GMC 2012 Terrain Owner'S Manual preview
2012 Terrain
Бренд: GMC Страницы: 428
Dodge 8W-30 Wiring Diagram preview
8W-30
Бренд: Dodge Страницы: 24
ULTIMATE SPEED 279619 Instructions For Use And Safety Manuallines preview
279619
Бренд: ULTIMATE SPEED Страницы: 40
Edelbrock 5756 Installation Instructions preview
5756
Бренд: Edelbrock Страницы: 1
Pogo Alert+ Operating Instructions Manual preview
Alert+
Бренд: Pogo Страницы: 40
Rugged Ridge 13551.33 Manual preview
13551.33
Бренд: Rugged Ridge Страницы: 3
Saleen 10-8002-C12167A Installation Manual preview
10-8002-C12167A
Бренд: Saleen Страницы: 6
Hellwig R-7694 Installation Instructions preview
R-7694
Бренд: Hellwig Страницы: 5
NavLinkz RL4-LR16-10 Manual preview
RL4-LR16-10
Бренд: NavLinkz Страницы: 26
Kia K900 2020 Vehicle Feature Tips preview
K900 2020
Бренд: Kia Страницы: 4
HardWire HWP132A User Manual preview
HWP132A
Бренд: HardWire Страницы: 18
BFT ESPAS10 MONEYBOX Installation And User Manual preview
ESPAS10 MONEYBOX
Бренд: BFT Страницы: 26
Edelbrock 70050 Instruction preview
70050
Бренд: Edelbrock Страницы: 29
Chrysler 2005 300 Manual preview
2005 300
Бренд: Chrysler Страницы: 374
Jegs 40824 Installation Instructions preview
40824
Бренд: Jegs Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды