manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1G-7 Fuel System: 

Fuel Pressure Relief Procedure

S4RS0A1706002

CAUTION:

This work must not be done when engine is 
hot. If done so, it may cause adverse effect to 
catalyst.

 

NOTE:
If ECM detects DTC(s) after servicing, clear 
DTC(s) referring to “DTC Clearance:  in 
Section 1A”.

 

1) Make sure that engine is cold.
2) Shift transaxle gear shift lever in “Neutral” (shift 

select lever in “P” range for A/T model), set parking 
brake and block drive wheels.

3) Remove relay / fuse box cover.
4) Disconnect fuel pump relay (1) from relay / fuse box 

(2).

5) Remove fuel filter cap in order to release fuel vapor 

pressure in fuel tank, and then reinstall it.

6) Start engine and run it until engine stops for lack of 

fuel. Repeat cranking engine 2 – 3 times for about 3 
seconds each time in order to dissipate fuel pressure 
in lines. Fuel connections are now safe for servicing.

7) After servicing, connect fuel pump relay (1) to relay / 

fuse box and install relay / fuse box cover.

Fuel Leakage Check Procedure

S4RS0A1706003

After performing any service on fuel system, check to 
make sure that there are no fuel leakages as follows.

1) Turn ON ignition switch for 3 seconds (to operate 

fuel pump) and then turn it OFF.
Repeat this (ON and OFF) 3 or 4 times and apply 
fuel pressure to fuel line until fuel pressure is felt by 
hand placed on fuel feed hose.

2) In this state, check to see that there are no fuel 

leakages from any part of fuel system.

Fuel Lines On-Vehicle Inspection

S4RS0A1706004

CAUTION:

Due to the fact that fuel feed line (1) is under 
high pressure, use special care when 
servicing it.

 

Visually inspect fuel lines for evidence of fuel leakage, 
hose crack and deterioration or damage.
Make sure all clamps are secure.
Replace parts as needed.

Fuel Pipe Removal and Installation

S4RS0A1706005

WARNING:

Before starting the following procedure, be 
sure to observe “Precautions on Fuel System 
Service: ” in order to reduce the risk or fire 
and personal injury.

 

Removal

1) Relieve fuel pressure in fuel feed line according to 

“Fuel Pressure Relief Procedure: ”.

2) Disconnect negative cable at battery.
3) Disconnect fuel pipe joint and fuel hose (3) from fuel 

pipe (2) at the front and rear of each fuel pipe 
referring to “Fuel Hose Disconnecting and 
Reconnecting: ”.

4) Mark the location of clamps (1) on fuel pipes (2), so 

that the clamps can be reinstalled to where they 
were.

5) Remove pipes (2) with clamp (1) from vehicle.
6) Remove clamp (1) from pipes (2).

1

I4RS0A170004-

1

I4RS0A170005-

2

1

3

I4RS0A170020-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

GARO TWIN+ Assembly Instructions / End User Instruction preview
TWIN+
Бренд: GARO Страницы: 23
GARO LS4 Wallmounted Operational Instructions preview
LS4 Wallmounted
Бренд: GARO Страницы: 15
Kolpin 25-9250 Owner'S And Operator'S Manual preview
25-9250
Бренд: Kolpin Страницы: 25
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Бренд: Metra Electronics Страницы: 2
Car-Interface CI-RL4-ELINK Manual preview
CI-RL4-ELINK
Бренд: Car-Interface Страницы: 23
RuggON VD04 Quick Start Manual preview
VD04
Бренд: RuggON Страницы: 2
TATA Motors nano genX Owner'S Manual preview
nano genX
Бренд: TATA Motors Страницы: 156
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Бренд: VER-MAC Страницы: 64
RBO RBO4038 Product Manual preview
RBO4038
Бренд: RBO Страницы: 15
Prorack WHISPBAR S53 Fitting Instructions For Basic Carrier preview
WHISPBAR S53
Бренд: Prorack Страницы: 10
Mercedes-Benz Sprinter 2003 Manual preview
Sprinter 2003
Бренд: Mercedes-Benz Страницы: 296
Calix group TYP MVP 823 Assembly Instructions preview
TYP MVP 823
Бренд: Calix group Страницы: 4
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Бренд: Whelen Engineering Company Страницы: 2
Ford TRANSIT CUSTOM Quick Reference Manual preview
TRANSIT CUSTOM
Бренд: Ford Страницы: 15
Honda 08L04-SZA-100 Installation Instructions preview
08L04-SZA-100
Бренд: Honda Страницы: 3
Autoplugin RCP-B1 Installation Manual preview
RCP-B1
Бренд: Autoplugin Страницы: 8
Blue Ox BX1120 Installation Instructions preview
BX1120
Бренд: Blue Ox Страницы: 5
ZENEC ZE-RVC85WA Mounting Instructions preview
ZE-RVC85WA
Бренд: ZENEC Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды