Suzuki RM-Z450 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 121

background image

6-33

NOTE:
•

Adding only water will dilute
the engine coolant and reduce
its effectiveness. Add specified
engine coolant.

•

This motorcycle does not have
an overflow tank at the end of
breather hose. Therefore,
engine coolant level may
decrease while riding. Check
the engine coolant level every
time before riding.

Radiator Hose Inspection

Inspect the radiator hoses for
cracks, damage or engine coolant
leakage. If any defects are found,
ask your Suzuki dealer to replace
the radiator hose with a new one.

BRAKES

This motorcycle has front and
rear disk brakes.

NOTE: Operating in mud, water,
sand or other extreme conditions
can cause accelerated brake
wear. If you operate your motorcy-
cle under these conditions, the
brakes must be inspected more
often than recommended in the
MAINTENANCE SCHEDULE.

Brake Hose Inspection

Inspect the brake hoses and hose
joints for cracks, damage or brake
fluid leakage. If any defects are
found, ask your Suzuki dealer to
replace the brake hose with a new
one.



WARNING

Failure to properly inspect and
maintain your motorcycle’s
brake systems can increase
your chance of having an acci-
dent.

Be sure to inspect the brakes
before each use according to
the INSPECTION BEFORE
RIDING section. Always main-
tain your brakes according to
the MAINTENANCE SCHED-
ULE.

«
...
90
91
92
93
94
...
»

Содержание RM-Z450


























































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z450

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Бренд: 3M Страницы: 84

Бренд: S&B Filters Страницы: 7

Бренд: Yamaha Страницы: 82

Apache RTR 160 HYPER EDGE 2015

Бренд: TVS Страницы: 60

Rocky Mountain-EXP SB-1

Бренд: Wolfman Страницы: 7

Бренд: Qingqi Страницы: 48

Бренд: Yadea Страницы: 100

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 142

Бренд: Yamaha Страницы: 118

Бренд: hepco & becker Страницы: 2

Бренд: DYNATEK Страницы: 1

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 3

Бренд: Arai Страницы: 2

Бренд: KTM Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды