Suzuki RM-Z450 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 121

background image

6-32

ENGINE COOLANT

COOLANT LEVEL

1. Check that the engine coolant

level is at the bottom of the
inlet hole. If not, replenish the
radiator with specified engine
coolant.

2. Tighten the radiator cap

1

securely.



WARNING

Engine coolant is harmful or
fatal if swallowed or inhaled.
Solution can be poisonous to
animals.

Do not drink antifreeze or cool-
ant solution. If swallowed, do
not induce vomiting. Immedi-
ately contact a poison control
center or a physician. Avoid
inhaling mist or hot vapors; if
inhaled, remove to fresh air. If
coolant gets in eyes, flush eyes
with water and seek medical
attention. Wash thoroughly
after handling. Keep out of the
reach of children and animals.



WARNING

You can be injured by scalding
fluid or steam if you open the
radiator cap when the engine is
hot.

Do not open the radiator cap
when the engine is hot. Wait
until engine cools.



CAUTION

Improperly tightening the radi-
ator cap will prevent the cool-
ing system from reaching the
specified operating pressure
and will cause overheat.

Tighten the radiator cap until it
locks firmly.

«
...
89
90
91
92
93
...
»

Содержание RM-Z450


























































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z450

Бренд: GIVI Страницы: 3

Бренд: Ohlins Страницы: 4

Бренд: SCHUBERTH Страницы: 41

Бренд: Paaschburg & Wunderlich Страницы: 2

Stealth Air Cleaner Kit

Бренд: S&S Cycle Страницы: 4

Бренд: Ducati Страницы: 77

Battery Relocation Kit

Бренд: BoxerCafe Страницы: 7

Бренд: Yamaha Страницы: 112

Бренд: Bajaj Страницы: 319

Бренд: DYNATEK Страницы: 8

Бренд: Eastwood Страницы: 8

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 7

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 3

Бренд: hepco & becker Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды