Suzuki RM-Z450 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 121

background image

3-13

Front Fork Tuning Procedure

Test ride the motorcycle and find out how the front suspension reacts
on various types of surface. According to the symptom noticed, adjust
the front fork to the best setting for rider and race track conditions. To
adjust, attempt changing fork oil capacity and compression and
rebound damping force following the instructions below.

NOTE:
•

When adjusting the front fork oil capacity, make sure that the oil
capacity is within the specified range. Also, the capacity should be
increased or decreased by 1 ml (0.034 US oz).

•

When adjusting the damping force, attempt turning the adjuster 1 to
2 click stops at a time for each adjustment.

Symptom

Section

Adjustment Procedure

Feels too hard overall • Jump

• Large bumps
• Series of medium

bumps

1. Adjust both compression and rebound damping

force to a softer setting.

2. Decrease fork oil capacity.
3. Change the spring with an optional softer one.

Feels too soft overall
and bottoms

• Jump
• Large bump
• When braking

1. Adjust the compression damping force to a stiffer

setting.

2. Increase fork oil capacity.
3. Change the spring with an optional stiffer one.

Feels too hard near
end of travel

• Jump

Decrease fork oil capacity.

Feels too soft near
end of travel and
bottoms harshly

• Jump
• Large bump

1. Adjust the compression damping force to a stiffer

setting.

2. Increase fork oil capacity.

Feels too hard in the
beginning of stroke

• Jump
• Large bump
• Series of medium

bumps

• Series of small

bumps

Adjust the compression damping force to a softer
setting.

Feels too soft and
unstable

• Series of medium

bumps

• Series of small

bumps

Adjust the rebound damping force to a stiffer setting.

Bounces

• Jump
• Large bump

Adjust the rebound damping force to a stiffer setting.

Bounces

• Series of small

bumps

Adjust the rebound damping force to a softer setting.

«
...
28
29
30
31
32
...
»

Содержание RM-Z450


























































































































Отзывы:

Нет отзывов

Похожие инструкции для RM-Z450

Бренд: Honda Страницы: 118

Бренд: Baja motorsports Страницы: 20

Бренд: Ohlins Страницы: 4

Бренд: Evotech Страницы: 84

Бренд: thousand Страницы: 32

Бренд: Pandora Страницы: 56

XV17ATMV(C) Road Star

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 118

Super Tenere ES 2022

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 282

Super Tenere ES 2020

Бренд: Yamaha Страницы: 130

Бренд: Yamaha Страницы: 211

Бренд: SUOMY Страницы: 26

Бренд: Leatt Страницы: 26

Бренд: Leatt Страницы: 26

Бренд: Dynafit Страницы: 21

Spyder RS Series

Бренд: Can-Am Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды