background image

22

Brake Lever (Parking Brake)

Check the brake lever play at the lever holder when the
lever is lightly pulled in towards the grip.

Rear brake (Parking brake) lever play: 6.0–8.0 mm

If adjustment is necessary, carry out the procedure
below:

1. Loosen the lock nut 

B

 and turn in the adjuster 

A

 as

far as it will go.

2. Turn the adjuster 

C

 clockwise or counterclockwise

to obtain the specified play.

3. Minor adjustments can now be made with the brake

lever adjuster 

A

Tighten the lock nut 

B

Set the lever cover 

D

.

4. After adjusting the play, check that the rear wheels

roll freely with the brake disengaged, the transmis-
sion in neutral, and the rear wheels off the ground.

5. Set the parking brake and check that the rear

wheels are locked by trying to move the vehicle
back and forth while it is in neutral.

6. Readjust the rear brake lever play if the rear wheels

could not roll freely or if the rear wheels didn’t lock in
step (2).

FRONT

FRONT AND REAR SUSPENSION ADJUSTMENT

Check for the spring setting of front and rear suspen-
sion.
This vehicle is delivered from the factory with its
adjusters set to the following positions.

#

A: Adjuster

REAR

Standard 

setting

FRONT

REAR

2

2

When adjusting either of the suspensions, be
sure to adjust both the right and left springs to
the same preload setting.

1

2

3

4

5

1

2

3

4

5

Содержание LT-A700XK5



































Отзывы: