Suzuki Intruder VZR1800 Скачать руководство пользователя страница 341

Страница: 341 / 586

COOLING AND LUBRICATION SYSTEM 8-11

THERMOSTAT

REMOVAL

• Remove the left air cleaner box. (

6-13)

• Place a rag under the thermostat cover.
• Remove the thermostat cover

• Remove the thermostat

INSPECTION

Inspect the thermostat pellet for signs of cracking.
Test the thermostat at the bench for control action, in the follow-
ing manner.

• Pass a string

between flange

of thermostat, as shown.

• Immerse the thermostat in the water contained in a beaker, as

shown in the illustration. Note that the immersed thermostat is
in suspension. Heat the water

by placing the beaker on a

stove

and observe the rising temperature on a thermome-

ter

• Read the thermometer just when opening the thermostat. This

reading, which is the temperature level at which the thermo-
stat valve begins to open, should satisfy the standard value.

Thermostat valve opening temperature

Standard: Approx. 88 °C (190 °F)

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Intruder VZR1800

Отзывы:

Похожие инструкции для Intruder VZR1800

Бренды по названию

Популярные бренды

Suzuki Intruder VZR1800, Руководство по обслуживанию

Результаты поиска

Содержание Intruder VZR1800

Отзывы:

Похожие инструкции для Intruder VZR1800

Бренды по названию

Популярные бренды