manualshive.com logo in svg

Suzuki Intruder VZR1800, Руководство по обслуживанию


Поделиться
Скачать
background image

1-10     GENERAL INFORMATION

CHASSIS

Front suspension ................................................. Inverted telescopic, coil spring, oil damped
Rear suspension .................................................. Link type, coil spring, oil damped
Front fork stroke ................................................... 130 mm (5.1 in)
Rear wheel travel ................................................. 118 mm (4.6 in)
Caster .................................................................. 31° 15’
Trail ...................................................................... 124 mm (4.9 in)
Steering angle...................................................... 37° (right & left)
Turning radius ...................................................... 3.3 m (10.8 ft)
Front brake........................................................... Disc brake, twin
Rear brake ........................................................... Disc brake
Front tire size ....................................................... 130/70R18M/C 63V, tubeless
Rear tire size ........................................................ 240/40R18M/C 79V, tubeless

ELECTRICAL

Ignition type.......................................................... Electronic ignition (Transistorized)
Ignition timing....................................................... 5° B.T.D.C at 900 r/min
Spark plug............................................................ NGK: CR8EK or DENSO: U24ETR
Battery.................................................................. 12 V 64.8 kC (18 Ah)/10 HR
Generator............................................................. Three-phase A.C. Generator
Main fuse ............................................................. 30 A
Fuse ..................................................................... 10/10/10/15/15/15 A
Headlight.............................................................. 12 V 60/55 W (H4)
Position light......................................................... 12 V 5 W ................................... For E-02, 19, 24
Front turn signal/position light .............................. 12 V 21/5 W .............................. For E-03, 28, 33
Front turn signal light .............................................12 V 21 W ................................. For the others
Rear turn signal light ............................................ 12 V 21 W
License light ......................................................... 12 V 5 W
Brake light/Taillight............................................... LED
Speedometer light................................................ LED
Tachometer light .................................................. LED
Fuel level indicator light ....................................... LED
Turn signal indicator light ..................................... LED
Neutral indicator light ........................................... LED
High beam indicator light ..................................... LED
Coolant temperature/Oil pressure Indicator light...... LED
FI indicator light .................................................... LED

CAPACITIES

Fuel tank capacity ................................................   18.5 L (4.9/4.1 US/lmp gal) ..... For E-33

  19.5 L (5.2/4.3 US/lmp gal) ..... For the others

Engine oil, oil change .......................................... 3 400 ml (3.6/3.0 US/Imp qt)

with filter change ............................... 3 600 ml (3.8/3.2 US/lmp qt)
overhaul............................................. 4 700 ml (5.0/4.1 US/lmp qt)

Final gear oil ........................................................   200 – 220 ml (6.8/7.0 – 7.4/7.7 US/Imp oz)
Coolant.................................................................     2.7 L (2.9/2.4 US/lmp qt)

These specifications are subject to change without notice.

Содержание Intruder VZR1800











































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Intruder VZR1800

KTM 450 SX-F 2019 Owner'S Manual preview
450 SX-F 2019
Бренд: KTM Страницы: 163
Gentex CVC M9 Operation And Maintenance Manual preview
CVC M9
Бренд: Gentex Страницы: 15
Christopeit Sport MB2 9840A Assembly And Exercise Instructions preview
MB2 9840A
Бренд: Christopeit Sport Страницы: 16
LAZER LZ6-BORA Manual preview
LZ6-BORA
Бренд: LAZER Страницы: 11
Shark SHKC7800N User Manual preview
SHKC7800N
Бренд: Shark Страницы: 16
hepco & becker 506.667 Quick Start Manual preview
506.667
Бренд: hepco & becker Страницы: 4
Buell 61861-01Y Instruction Sheet preview
61861-01Y
Бренд: Buell Страницы: 4
Malaguti Drakon 50 Manual preview
Drakon 50
Бренд: Malaguti Страницы: 303
APRILIA ETX 150 Service Station Manual preview
ETX 150
Бренд: APRILIA Страницы: 170
Denali DialDim DNL.WHS.22800 Instruction Manual preview
DialDim DNL.WHS.22800
Бренд: Denali Страницы: 3
Denali DNL.WHS.084 Installation Instructions preview
DNL.WHS.084
Бренд: Denali Страницы: 3
Bell Sports Helmet Owner'S Manual preview
Helmet
Бренд: Bell Sports Страницы: 20
Peg-Perego DUCATI IGCS0703 Use And Care Manual preview
DUCATI IGCS0703
Бренд: Peg-Perego Страницы: 24
KTM 2015 450 Rally Factory Replica Owner'S Manual preview
2015 450 Rally Factory Replica
Бренд: KTM Страницы: 133
Royal Enfield Classic 350 Owner'S Manual preview
Classic 350
Бренд: Royal Enfield Страницы: 100
Cocoon BT42740 Instruction Manual preview
BT42740
Бренд: Cocoon Страницы: 16
Kabuto Japan RT33 Instruction Manual preview
Japan RT33
Бренд: Kabuto Страницы: 29
National Cycle Fly Boy N27410 Quick Start Manual preview
Fly Boy N27410
Бренд: National Cycle Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды