manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

EXTENSION CASE

Removal/Installation

1) Remove select cable lever (1) and gear shift stop bolt (2).
2) Remove shift & select shaft assembly (3).
3) Support engine/transmission assy on jack.
4) Disconnect vehicle speed sensor coupler and remove engine

rear mounting.

5) Remove bolts securing extension case to transmission case,

and then take off extension case.

6) Remove extension case seal (1) as necessary.

Reverse removal procedure for installation referring to 7A–24.

DISMOUNTING

1) Disconnect negative (–) cable from battery terminals and hoist

vehicle.

2) Disconnect back-up light switch lead wire at coupler.
3) Disconnect Black/Yellow lead wire and positive (+) cord from

starting motor. Remove starting motor from transmission case.

4) Disconnect coupler from speed sensor and free its harness

from transmissions.

5) Remove drain plug to drain oil in transmission.

1. Back-up light switch
2. Back-up light switch coupler
3. Speed sensor
4. Clamp

6) Remove transmission front case cap and take off clutch cable

end (1) from clutch release fork (2). Disconnect clutch cable as-
sembly from transmission.

7) Remove transmission to body ground cable bolt (4).

3. Clutch cable

7A-6

MANUAL TRANSMISSION

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

ZAPTEC Go Instruction Manual preview
Go
Бренд: ZAPTEC Страницы: 240
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Бренд: Axxess Страницы: 8
PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Бренд: PullRite Страницы: 10
Chevrolet 2013 Spark Specifications preview
2013 Spark
Бренд: Chevrolet Страницы: 2
BMW E39/2 Installation Instructions Manual preview
E39/2
Бренд: BMW Страницы: 21
Van Guard VG273 Fitting Instructions preview
VG273
Бренд: Van Guard Страницы: 3
Fisher Body FOLDING TOP 1971 Service Manual preview
FOLDING TOP 1971
Бренд: Fisher Body Страницы: 37
Manik 519952T Installation Instructions preview
519952T
Бренд: Manik Страницы: 2
NavInc CP-PEU-GV3 Manual preview
CP-PEU-GV3
Бренд: NavInc Страницы: 6
E&G Classics Denali 1094-0185-15 Instruction Manual preview
Denali 1094-0185-15
Бренд: E&G Classics Страницы: 3
Metra Electronics 99-7803G Wiring Instructions preview
99-7803G
Бренд: Metra Electronics Страницы: 2
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Бренд: Mitsubishi Страницы: 362
ROADGEAR RGABM1 User Manual & Fitting Instructions preview
RGABM1
Бренд: ROADGEAR Страницы: 2
Honda 2010 Accord Coupe Owner'S Manual preview
2010 Accord Coupe
Бренд: Honda Страницы: 410
Scion 2013 iQ Warranty & Maintenance Manual preview
2013 iQ
Бренд: Scion Страницы: 58
Audi S4 Biturbo Buyer'S Manual preview
S4 Biturbo
Бренд: Audi Страницы: 9
Jacob Jensen Electronic Parking Disc 3 User Manual preview
Electronic Parking Disc 3
Бренд: Jacob Jensen Страницы: 17
Brodit 841488 Quick Start Manual preview
841488
Бренд: Brodit Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды