FI SYSTEM/ CVT SYSTEM 6-25
MALFUNCTION CODE AND DEFECTIVE CONDITION
MALFUNCTION
CODE
DETECTED ITEM
DETECTED FAILURE CONDITION
CHECK FOR
C00
NO FAULT
–––––––––––
C11
Camshaft position
sensor
The signal does not reach ECM for more than 2 sec. after
receiving the starter signal.
The camshaft position sensor wiring and mechanical parts.
(Camshaft position sensor, intake cam pin, wiring/coupler con-
nection)
C12
Crankshaft position
sensor
The signal does not reach ECM for more than 2 sec. after
receiving the starter signal.
The crankshaft position sensor wiring and mechanical parts.
(Crankshaft position sensor, wiring/coupler connection)
C13
Intake air pressure
sensor
The sensor should produce following voltage.
(0.50 V
sensor voltage < 4.85 V)
Without the above range, C13 is indicated.
Intake air pressure sensor, wiring/coupler connection.
C14
Throttle position
sensor
The sensor should produce following voltage.
(0.20 V
sensor voltage < 4.80 V)
Without the above range, C14 is indicated.
Throttle position sensor, wiring/coupler connection.
C15
Engine coolant
temperature sensor
The sensor voltage should be the following.
(0.15 V
sensor voltage < 4.85 V)
Without the above range, C15 is indicated.
Engine coolant temperature sensor, wiring/coupler connection.
C16
Speed sensor
The speed sensor signal is not input for more than 3 sec. during
vehicle deceleration.
Speed sensor, wiring/coupler connection.
C21
Intake air temperature
sensor
The sensor voltage should be the following.
(0.15 V
sensor voltage < 4.85 V)
Without the above range, C21 is indicated.
Intake air temperature sensor, wiring/coupler connection.
C22
Atmospheric pressure
sensor
The sensor voltage should be the following.
(0.50 V
sensor voltage < 4.85 V)
Without the above range, C22 is indicated.
Atm. pressure sensor, wiring/coupler connection.
C23
Tip over sensor
The sensor voltage should be the following for more than 2 sec.
after ignition switch turns ON.
(0.20 V
sensor voltage < 4.80 V)
Without the above value, C23 is indicated.
Tip over sensor, wiring/coupler connection.
C24 or C25
Ignition signal
Crankshaft position sensor (pick-up coil) signal is produced but
signal from ignition coil is interrupted continuous by 4 times or
more. In this case, the code C24 or C25 is indicated.
Ignition coil, wiring/coupler connection, power supply from the
battery.
Содержание AN650 2002
