®
12/2015 ENG
1
SUZUKI Deutschland GmbH, Suzuki-Allee 7, D-64625 Bensheim
Description:
Carbon
frame cover center - matt finish
Part Number:
990D0-04K60-CRB
Applications:
GSX-S1000/F AL6
Mounting Time:
30 Min
Ref. Description
Qty.
1
1
Carbon frame cover center
1
2
Mounting Instructions
1
2
Ref. Description
1
2
1 Allan key (5mm)
2 Screw driver (PH2 and PH3)
1. Check that the kit includes all the parts listed on the first page.
2. Check each part in the kit for scratches or any form of damage.
3. Park the vehicle on level ground.
4. Remove the ignition key from the switch and store it in a safe place.
5. Protect any items removed or to be installed from scratches by placing them on a
soft cloth first before putting them on the ground.
6. Use care not to cause any damage to the body of the vehicle during installation
of the accessory.
!
CAUTION
If you do not feel technical qualified to install this product on your own,
please consult with your nearest SUZUKI dealer.
Tighten bolts to the torque indicated in the right
table as standard value unless otherwise explicitly
specified. The value shows conventional or “4”
marked bolt tightening torque. For other bolts not
listed in the table, please refer to owner’s manual.
Diameter
(mm)
Tightening Torque
N·m
kgf-m lbf-ft
5
3.0
0.3
2.2
6
5.5
0.55
4.0
8
13.0
1.3
9.5
10
29.0
2.9
21.0
NOTE: Read these instructions carefully before assembly and examine
whether all parts are enclosed in accordance with the parts list.
1. Remove passenger and driver seat according to owner's manual. (Fig 1)
2. Remove frame covers (A) by pulling velcro tape (H) and two pins (J) from positioning
brackets, then slide the frame covers backwards.(Fig 2 and 3)
3. Remove screws (D) from left and right (8 pcs) rear frame side covers (B). (Fig 4)
4. Unhook front pin (F) and hooks (L) (2 pcs) of rear frame side covers (B), then slide
forwards to unhook it from rear center cover (C), then lift to remove it. (Fig 5 and 6)
5. Remove screws (E) (3 pcs) from rear center cover (C). (Fig 7)
6. Lift front brackets (G) of rear center cover (C) from its position and slide it backward
to remove it. (Fig 8)
7. Assemble carbon rear center cover (C) in reverse sequence. Please make sure that
brackets (G) are hooked into gaps on side plastic covers. Press together to place in
final position. (Fig 8)
8. Assemble the side rear frame cover (B) in reverse sequence.
9. Assemble the frame covers (A) in reverse sequence (Fig 9). Please make sure that
front hook (I), tank bracket (K) and pins (J) (Fig 2) are mounted correctly. Push side
frame cover to fix the velcro tape (H). (Fig 9)
10. Install driver and passenger seat according to owner's manual.
To clean, rinse carbon part with water to remove grit and soften dirt. Use a mild non -
abrasive liquid soap, plenty of warm water, and a clean flannel cloth or soft chamois.
Rinse well to remove all soap residue. Pat dry, do not wipe.
Due to mounted SUZUKI Genuine Accessories the service and maintenance flat rate
might be affected. Dismounting/Mounting of SUZUKI Genuine Accessories is
possibly necessary for service and maintenance.
!
WARNING /
!
CAUTION /
NOTICE
/
NOTE
.
Please read this manual and follow its instructions carefully. To emphasize special
information, the symbol
!
and the words
WARNING, CAUTION,
NOTICE
and
NOTE
have special meanings. Pay particular attention to messages highlighted by these
signal words:
!
WARNING
Indicates a potential hazard that could result in death or serious injury.
!
CAUTION
Indicates a potential hazard that could result in minor or moderate injury.
NOTICE
Indicates a potential hazard that could result in vehicle or equipment damage.
NOTE: indicates special information to make maintenance easier or instructions
clearer.
Precautions for
Installation
Tightening
Torque
Mounting
Care and
Maintenance
Inspection
Part List
Tools Required
Important
MOUNTING INSTRUCTIONS
SUZUKI GENUINE ACCESSORIES
