manualshive.com logo in svg

Suzuki 2007 XL7, Руководство по обслуживанию


Поделиться
Скачать
background image

5- ii Table of Contents

Symptoms - Automatic Transmission 

Shift Lock Control.........................................  5A–155

Transmission Adaptive Learn and 

Transmission Neutral Learn .........................  5A–155

Road Test.......................................................  5A–157
Torque Converter Diagnosis ..........................  5A–157
Flexplate/Torque Converter Vibration Test ....  5A–159
Stall Speed Test.............................................  5A–159
Engagement Delay Test.................................  5A–160
Noise and Vibration Analysis .........................  5A–161
Clutch Plate Diagnosis ...................................  5A–161
Engine Coolant/Water in Transmission..........  5A–162
Fluid Leak Diagnosis......................................  5A–162
Case Porosity Repair .....................................  5A–165
Transmission Fluid Cooler Flushing and 

Flow Test......................................................  5A–165

Transmission Overheats ................................  5A–170
No Forward and Reverse ...............................  5A–171
Slips in Drive or No Drive ...............................  5A–172
Slips in Reverse or No Reverse .....................  5A–173
Engagement Time From Park or Neutral to 

Drive is Not Within Specifications ................  5A–174

Engagement Time From Park or Neutral to 

Reverse is Not Within Specifications ...........  5A–174

Engine Stalls During Reverse or 

Drive Engagement .......................................  5A–175

Slips on Acceleration......................................  5A–175
Harsh Feel at Light Acceleration or 

Deceleration Without Causing an Upshift or 
Downshift .....................................................  5A–176

No 1-2 Upshift ................................................  5A–177
No 2-3 Upshift ................................................  5A–177
No 3-4 Upshift ................................................  5A–178
No 4-5 Upshift ................................................  5A–178
No 5-4 Downshift............................................  5A–179
No 4-3 Downshift............................................  5A–179
No 3-2 Downshift............................................  5A–180
No 2-1 Downshift............................................  5A–180
Torque Converter Clutch Stuck On or Off ......  5A–181
No Engine Braking in Fourth Gear .................  5A–181
No Engine Braking in Third Gear ...................  5A–182
No Engine Braking in Second Gear ...............  5A–182
No Response to Movement of Shift Lever .....  5A–183
Transmission Attempts to Move but 

Appears Locked Up......................................  5A–183

Vibration at Idle ..............................................  5A–183
Vibration While Driving...................................  5A–183
Hum or Rattle Noise at Idle ............................  5A–184
Whine/Growl Noise That Changes with 

Vehicle Speed ..............................................  5A–184

Automatic Transmission Fluid Leaks .............  5A–184
Harsh Park or Neutral to Drive Engagement..  5A–186
Harsh Park or Neutral to 

Reverse Engagement ..................................  5A–187

Harsh Upshift .................................................  5A–188
Harsh Shift on Coastdown .............................  5A–189
Harsh Forced Downshift.................................  5A–190
Shift Lever Does Not Move with 

Brake Pedal Depressed ...............................  5A–192

Shift Lever Can Be Moved without 

Brake Pedal Depressed ...............................  5A–193

Repair Instructions.......................................... 5A–194

Transmission Fluid Check..............................  5A–194
Line Pressure Check......................................  5A–195
Transaxle Fluid Replacement ........................  5A–197
Transmission Control Lever Knob 

Replacement ................................................  5A–198

Automatic Transmission Control Indicator 

Replacement ................................................  5A–199

Transmission Control Boot Replacement.......  5A–200
Shift Control Replacement .............................  5A–201
Shift Lock Solenoid/

Switch Assembly Replacement....................  5A–202

Transmission Control Bracket Replacement..  5A–203
Shift Control Cable Replacement...................  5A–203
Shift Control Cable Adjustment ......................  5A–205
Shift Control Cable Bracket Replacement......  5A–206
Automatic Transmission Range Selector Lever 

Replacement ................................................  5A–207

Transmission Control Module Replacement ..  5A–208
Transmission Control Module 

Programming and Setup ..............................  5A–210

Transaxle Brace Replacement.......................  5A–210
Transmission Mount Inspection .....................  5A–211
Transmission Front Mount Replacement .......  5A–211
Transmission Rear Mount Replacement 

(Getrag 760 Transfer Case) .........................  5A–212

Transmission Mount Replacement - 

Left Side .......................................................  5A–213

Transmission Rear Mount Bracket 

Replacement (AWD) ....................................  5A–214

Transmission Rear Mount Bracket 

Replacement (FWD) ....................................  5A–215

Transmission Mount Bracket Replacement - 

Left Side .......................................................  5A–215

Fluid Level Indicator Replacement.................  5A–216
Input Speed Sensor Replacement .................  5A–217
Output Speed Sensor Replacement ..............  5A–218
Control Valve Body Cover Replacement........  5A–219
Automatic Transmission Wiring Harness 

Replacement ................................................  5A–220

Control Valve Body Replacement ..................  5A–222
Oil Cooler Line Replacement .........................  5A–225
Fluid Cooler Pipe Seal Replacement .............  5A–226
Drive Axle Shaft Seal Replacement (Left)......  5A–228
Drive Axle Shaft Seal Replacement (Right) ...  5A–229
Transaxle Replacement .................................  5A–230
Torque Converter Assembly Removal ...........  5A–232
Holding Fixture Installation.............................  5A–232
Transmission Fluid Draining...........................  5A–233
Input and Output Speed Sensor Removal .....  5A–234
Transmission Control Module Removal .........  5A–234
Control Valve Body Cover Removal...............  5A–234
Wiring Harness Removal ...............................  5A–235
Control Valve Body Assembly Removal.........  5A–236
Fluid Pump Assembly Removal .....................  5A–237
Second Coast, Second Clutch Hub and 

Second Clutch Sprag Assembly Removal ...  5A–237

Torque Converter Housing Removal..............  5A–237

Содержание 2007 XL7
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2007 XL7

JANE be cool boosty Manual preview
be cool boosty
Бренд: JANE Страницы: 21
Waeco MagicWatch MWE800 Installation And Operating Manual preview
MagicWatch MWE800
Бренд: Waeco Страницы: 212
Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Бренд: Genesis Страницы: 3
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Бренд: Metra Electronics Страницы: 2
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Бренд: Haibang Страницы: 6
Saab 32 025 888 Installation Instructions preview
32 025 888
Бренд: Saab Страницы: 3
Nav TV NAV-INREN Quick Manual preview
NAV-INREN
Бренд: Nav TV Страницы: 2
Metra Electronics 99-8714 Installation Instructions Manual preview
99-8714
Бренд: Metra Electronics Страницы: 8
Pet Gear TRI-FOLD PG9300RF Instruction Manual preview
TRI-FOLD PG9300RF
Бренд: Pet Gear Страницы: 4
ZAPTEC ZapCharger Portable C1 User Manual preview
ZapCharger Portable C1
Бренд: ZAPTEC Страницы: 20
FALCON RIDGE Bobcat 3400 Instructions For Installation And Care preview
Bobcat 3400
Бренд: FALCON RIDGE Страницы: 4
Brink 4698 Fitting Instructions Manual preview
4698
Бренд: Brink Страницы: 26
Belkin TuneBase F8Z442 User Manual preview
TuneBase F8Z442
Бренд: Belkin Страницы: 162
Edelbrock Honda XR400 Instruction Supplement preview
Honda XR400
Бренд: Edelbrock Страницы: 2
Hudson Super Six 1916 Reference Book preview
Super Six 1916
Бренд: Hudson Страницы: 77
VP Autoparts 419420 Installation preview
419420
Бренд: VP Autoparts Страницы: 2
Mazda Auto-Dimming Mirror User Manual preview
Auto-Dimming Mirror
Бренд: Mazda Страницы: 2
Toyota 1998 Celica Owner'S Manual preview
1998 Celica
Бренд: Toyota Страницы: 204

Бренды по названию

Популярные бренды

Загрузить еще бренды