E N G L I S H •
User's manual
11
IMPORTANT: This appliance is not intended
for use by persons (including children) with re-
duced physical, sensory or mental capabilities
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by
a person responsible for their safety. Children
should be supervised to ensure they do not use
the devices as toys.
TOOL USE AND CARE
Do not force the power tool. Use the correct
tool for the application. The correct tool will
do the job better and more safely at the rate
that it was designed to work at.
Do not use tools if switch does not turn it on or
off. Any tool that cannot be controlled whith
the switch is dangerous and must be repaired.
Disconnect the plug from the power source
before making any adjustments, changing ac-
cessories or storing the tool. This preventive
safety measures reduce the risk of accidental
starting of the tool.
When the power tool is not in use, store it out
of the reach of children, and do not allow in-
dividuals who are not familiar with the power
tool or these instructions to operate it. Power
tools are dangerous in the hands on untrained
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the
operation of the power tool. If it is damaged,
have it repaired before using. Many accidents
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving
parts, breakage parts, and any other condition
that may affect the tools operation. If you find
a damaged tool, take it to service before use it.
Use only accessories that are recommended by
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened
edges, are less likely to stuck in workpieces or
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and diferential switch
when you are using an electric equipment.
SERVICE
Tool service must be perfomed only by quali-
fied repair personnel. Service or maintenance
performed by unqualified personnel could re-
sult in a risk of injury.
SPECIFIC SAFETY RULES FOR
AIR COMPRESSORS
IMPORTANT:
This machine is intended to
generate compressed air required for the oper-
ation of air tools. Any use for medical purpos-
es, food processing as well as filling of oxygen
cylinders for breathing equipment is not per-
mitted. Explosive, combustible gases or gases
detrimental to health may not be compressed.
Operation in hazardous locations is not permit-
ted. Any other use is not a as specified, altera-
tion of the machine or use of parts that are not
approved by the equipment manufacturer, can
cause unforeseeable damage!
• Children, juveniles and persons not having
been instructed in its usage are not permitted
to operate this machine and any air tools con-
nected to it.
WARNING: Before connecting a tool to a
power source (receptacle, outlet, etc.) be sure
that the voltage supply is the same as that
specified on the nameplate of the tool.
A power source with a higher voltage than that
specified for the tool can result in serious injury
to the user, as well as damage to the tool.
Using a power source with a voltage less than
the nameplate rating is harmful to the motor.
Always unplug before making any adjustments
or maintenance, including renewing the lubri-
cating oil.
• To reduce the risk of fire or explosion, never
spray flammable liquids in a confined area.
It is normal for the compressor motor and pres-
sure switch to produce sparks during use. If
sparks come into contact with petrol vapours
or solvents, they may ignite and the vapours
can cause a fire or explosion.
• Always operate the compressor in a well ven-
tilated area. Do not smoke while spraying.
Do not spray where sparks or flames are pres-
ent. Keep the compressor as far away from the
spray area as possible.
• Do not use welding equipment in close prox-
imity to the compressor. Do not weld anything
COMP425A manual.indd 11
23/06/15 14:34
