FUNCTION DESCRIPTION
Listening to the FM Radio from the Speaker
1. To select FM use “MODE”button on unit main panel or from remote control or from remote control press
“FM” .
2. From the unit control panel. Long press to scan for station or press to manually access
preset stations up or down.
3. From remote control press “SCAN” to scan for FM frequency or press to manually select preset
station up or down.
4. “FM Antenna” to be used for better reception for FM station.
/
/
FUNCTION DESCRIPTION
Using Microphone
1. When using Microphone-plug your microphone into the microphone jack on unit main control panel .
2. Use the MIC VOL knob to control the voice level of the microphone
3. Use the “ECHO” knob to control microphone echo.
Using Guitar Jack.
1. When using Guitar-plug your guitar into the guitar jack on unit main control panel.
2. Use the Guitar VOL knob to control the volume level of the Guitar.
“BASS” & “TREBLE” on unit control panel can be used to adjust sound when using MICRO microSD Card,
USB, FM. “EQ”
button on unit control panel or remote control can be used to adjust sound effect to preset levels.
1
2
OPERATION
INSTRUCTION FOR KARAOKE & WIRELESS MICROPHONE
1. Insert the microphone plug into the microphone input MIC2.
2. Adjust the microphone volume knob MIC VOL for proper volume. Then adjust the echo depth to the proper
position. Now you can start the karaoke.
3. Open wireless MIC “ on & off ” button, Adjust the microphone volume knob MIC VOL for proper volume.
and adjust the echo depth to the proper position. The you can start the wireless Microphone.
1. Battery is integrated in the unit with an auto protection function. When the battery is out of power and
you need to recharge your speaker unit be sure the power switch is ON before you connect the system to
110V-240V power plug. When your unit is charging the red LED indicator will be ON. the unit, the battery
auto protection will take effect and the unit will NOT charge.
2. Full recharge takes 8-12 hours.
3. Voltage for recharge must be ~110V-240V
4. When you are using your unit while it is plugged to an external power source, be sure the battery switch
is ON.
5. To protect the life span of the built in battery, be sure to fully charge your unit on the same day the
battery runs out. Not charging your unit right away can hurt the long term life span of your unit.
6. When you change fuse, please use model (10A)
Matters need attention
1. Please press the “MODE” button to start the Bluetooth connection. This will turn on the Bluetooth
flashing LED light on the control panel.
2. Your unit will now be ready to pair with your mobile device via Bluetooth. From your mobile device scan
for “bt-speaker” . The password for connection is “0000“ and once you have paired your device to the DJ
system, the LED flashing light will become solid.
3. You can control the volume and tracks from the unit’s control panel or from your external Bluetooth
enabled device.
Bluetooth Connection
SPECIFICATIONS & DIMENSIONS
System Type:
12" Woofers/ & 1" Tweeters
Frequency Response
40Hz-20KHz
Impedance
4ohm
Peak Power Capacity
250 Watts
N.W. 10.97lbs.
G.W. 13.18lbs.
Dimensions
Specifications:
15.07" x 12.99" x 22.91"
RMS Power
15Watts
Using Aux( LINE IN 3.5mm)
1. To select Aux use ” MODE” button on unit main panel or from remote control “LINE” will show on display
2. Disconnect USB, TF Microphone while using Aux.
Record Function
Long press: IN the recording.
Short press: play the recording and play USB conversion.
REMARK: Need to insert the USB/microSD Card when recording.
When recording the sound from outside (such as the voice of people) need to use WIRELESS MIC / WIRED
MIC.
When recording AUX IN / FM no need to use WIRELESS MIC / WIRED MIC just insert USB.
1.Open the carton box to check the enclosurer:
Instruction book 1PC
Power line 1PC
Wired microphone: 1PC
Remote control( IR sensor distance :arround 6m): 1PC
Installation and play:
Using USB/microSD
1.Plug in your USB Disk or SD Card in the slots provided. Please make sure you use the correct file format
in your media devices – MP3 FILES ONLY and correct mode should be selected.
2.Please remember to turn off the power of the Speaker before removing the USB Disk or SD Card.
ICBM-PAN
REMOTE CONTROL FUNCTION