Supero H8SGL Скачать руководство пользователя страница 15

Страница: 15 / 74

Chapter 1: Introduction

1-7

Motherboard Features

CPU

Single AMD Opteron 6100 series (Socket G34 type) processor

•

Note: Refer to our web site for details on supported processors.

Memory

Single/Dual/Tri/Quad channel DIMM slots supporting up to 128 GB of DDR3-

•

1333/1066/800 registered ECC SDRAM or 32 GB of DDR3-1333/1066/800 MHz

unbuffered ECC/non-ECC SDRAM

Note: Refer to Section 2-4 before installing memory and our web site for recommended DIMMs.

Chipset

AMD SR5650 chipset and one SP5100 Southbridge chipset

•

Expansion Slots

One (1) PCI-Express x8 (in x16 slot) Gen. 2

•

One (1) PCI-Express x8 Gen. 2

•

One (1) PCI-Express x4 (in x8 slot) Gen. 2

•

Three (3) PCI slots

•

BIOS

16 Mb AMIBIOS

•

SPI Flash ROM

APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), SMBIOS

•

2.3, Real Time Clock Wakeup, Plug and Play (PnP), BIOS resume hot keys,

Hardware BIOS Virus Protection

PC Health Monitoring

Onboard voltage monitors

•

Fan status monitor with fi rmware/software on/off and speed control

•

Watch Dog

•

Environmental temperature monitoring via BIOS

•

Power-up mode control for recovery from AC power loss

•

System resource alert (via included utility program)

•

Auto-switching voltage regulator for the CPU core

•

CPU thermal trip support

•

C temperature sensing logic

Chipkill Support

•

Содержание H8SGL











































































Результаты поиска

Содержание H8SGL

Отзывы:

Похожие инструкции для H8SGL

Бренды по названию

Популярные бренды

Supero H8SGL, Руководство пользователя

Результаты поиска

Содержание H8SGL

Отзывы:

Похожие инструкции для H8SGL

Бренды по названию

Популярные бренды