Supero H8DM3-2 Скачать руководство пользователя страница 12

Страница: 12 / 78

1-6

H8DM3-2/H8DMi-2 User’s Manual

Serverboard Features

CPU

• Single or dual AMD Opteron 2000 Series Socket F type processors

Memory

• Eight dual/single channel DIMM slots supporting up to 64 GB of DDR2-667 or

32 GB of DDR2-533/400 registered ECC SDRAM

Note: Memory capacities are halved for single CPU systems. Refer to Section 2-4 before installing.

Chipset

• nVidia MCP55 Pro

• AMD-8132

Expansion Slots

• Two (2) PCI-Express x8 slots

• One (1) PCI-Express x4 slot

• One (1) PCI-X 133 MHz slot

• Two (2) PCI-X 133/100 MHz slots*

• One (1) low-profi le SIMLP slot (for IPMI card)

*These slots share a bus and so can only support up to 100 MHz when cards

are installed in both slots.

BIOS

• 8

AMIBIOS

LPC Flash ROM

• APM 1.2, DMI 2.3, PCI 2.2, ACPI 2.0, SMBIOS 2.3, Plug and Play (PnP)

PC Health Monitoring

• Onboard voltage monitors for two CPU cores, 3.3V, +5Vin, +12Vin, 5V stby and

battery voltage

• Fan status monitor with fi rmware/software on/off and speed control

• Watch

Dog

• Environmental temperature monitoring via BIOS

• Power-up mode control for recovery from AC power loss

• System resource alert (via included utility program)

• Pulse Width Modulated (PWM) fan connectors (FAN7 and FAN8 only)

• Auto-switching voltage regulator for the CPU core

Содержание H8DM3-2















































































Результаты поиска

Содержание H8DM3-2

Отзывы:

Похожие инструкции для H8DM3-2

Бренды по названию

Популярные бренды

Supero H8DM3-2, Руководство пользователя

Результаты поиска

Содержание H8DM3-2

Отзывы:

Похожие инструкции для H8DM3-2

Бренды по названию

Популярные бренды