Supero AS2021M-82R+ Скачать руководство пользователя страница 88

Страница: 88 / 104

7-16

AS2021M-T2R+/2021M-82R+ User's Manual

Startup Delay

Use this setting to Enable or

Disable

the startup delay.

Event Message for PEF Action

Use this setting to Enable or

Disable

event messages for a PEF action.

BMC Watch Dog Timer Action

This setting is used to set the Watch Dog function. The options are

Disabled

Reset System, Power Down and Power Cycle.

7-4 Boot

Menu

This feature allows the user to conﬁ gure the following items:

Boot Device Priority

This feature allows the user to prioritize the boot sequence from the available

devices.

Hard Disk Drives

This feature allows the user to specify the boot sequence from available hard disk

drives.

Removable Drives

This feature allows the user to specify the Boot sequence from available remov-

able drives.

CD/DVD Drives

This feature allows the user to specify the Boot sequence from available CD/DVD

drives.

Содержание AS2021M-82R+









































































































Результаты поиска

Содержание AS2021M-82R+

Отзывы:

Бренды по названию

Популярные бренды

Supero AS2021M-82R+, Руководство пользователя

Результаты поиска

Содержание AS2021M-82R+

Отзывы:

Бренды по названию

Популярные бренды