Supermicro X11SSE-F Скачать руководство пользователя страница 67

Страница: 67 / 98

Chapter 4: BIOS

SR-IOV Support

Use this feature to enable or disable Single Root IO Virtualization Support. The options are

Disabled

and Enabled.

CPU MICRO-LP PCI-E 3.0 X8 OPROM

Use this feature to select which firmware type to be loaded for the add-on card in this slot.

The options are Disabled,

Legacy

, and EFI.

Onboard Video Option ROM

Use this item to select the Onboard Video Option ROM type. The options are Disabled,

Legacy,

and EFI.

Network Stack

Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible

Firmware Interface) for network stack support. The options are

Enabled

and Disabled.

IPv4 PXE Support

Select Enabled to enable IPv4 PXE boot support. The options are

Enabled

and Disabled.

IPv6 PXE Support

Select Enabled to enable IPv6 PXE boot support. The options are Enabled and

Disabled

PXE boot wait time

Use this option to specify the wait time to press the ESC key to abort the PXE boot. Press
"+" or "-" on your keyboard to change the value. The default setting is

Media detect count

Use this option to specify the number of times media will be checked. Press "+" or "-" on your
keyboard to change the value. The default setting is



Super IO Configuration

The following Super IO information will display:

•

Super IO Chip AST 2400

Super IO Chip Logical Device(s) Configuration



Serial Port 1 Configuration

This submenu allows the user the configure settings of Serial Port 1.

Содержание X11SSE-F



































































































Результаты поиска

Содержание X11SSE-F

Отзывы:

Похожие инструкции для X11SSE-F

Бренды по названию

Популярные бренды

Supermicro X11SSE-F, Руководство пользователя

Результаты поиска

Содержание X11SSE-F

Отзывы:

Похожие инструкции для X11SSE-F

Бренды по названию

Популярные бренды