Supermicro SuperStorage SSG-136R-NR32JBF Скачать руководство пользователя | Manualshive

Страница: 18 / 75

background image

18

SuperStorage SSG-136R-NR32JBF User's Manual

Note:

The rails have a locking tab, which serves two functions. First, it locks the system into

place when installed and pushed fully into the rack (its normal operating position). In addition,
these tabs lock the system in place when fully extended from the rack. This prevents the
system from coming completely out of the rack when pulled out for servicing.

Figure 2-1. Identifying the Rail Sections

2.3 Installing the System into a Rack

This section provides information on installing the 136TS-R1K04JP-R2 chassis into a rack
unit with the rails provided. Due to the variety of rack units on the market, the assembly

procedure might differ slightly. You should also refer to the installation instructions that came

with the rack unit you are using.

Identifying the Sections of the Rack Rails

The SSG-136R-NR32JBF includes two rack rail assemblies in the rack mounting kit. Each
assembly consists of three sections: An inner chassis rail which secures directly to the chassis,
an outer rail that secures to the rack, and a middle rail which extends from the outer rail.

These assemblies are specifically designed for the left and right side of the chassis.

Inner Rail

Rail Assembly

(Shown with Rails
Retracted)

This Side Faces
Outward

Locking Tab

Middle Rail

Outer Rail

«
...
16
17
18
19
20
...
»

Содержание SuperStorage SSG-136R-NR32JBF












































































Отзывы:

Нет отзывов

Похожие инструкции для SuperStorage SSG-136R-NR32JBF

Бренд: ECKELMANN Страницы: 134

301160U - 1TB Ethernet Disk RAID Network Attached...

Бренд: LaCie Страницы: 5

Бренд: LaCie Страницы: 6

Бренд: Quantum Страницы: 78

AccuRAID AR316X12

Бренд: Sans Digital Страницы: 8

OneTouch III FireWire 800GB

Бренд: Maxtor Страницы: 8

Бренд: IBM Страницы: 122

Бренд: QNAP Страницы: 63

Бренд: LaCie Страницы: 28

Cold Frame Single

Бренд: Palram Страницы: 11

REPLACE TAPE DRIVE IN STORAGELOADER VXA...

Бренд: Tandberg Data Страницы: 10

STORAGE CAB4000 -

Бренд: Tandberg Data Страницы: 13

USO-HA D500 Series

Бренд: STONEFLY Страницы: 58

Бренд: Galvo Shed Страницы: 8

5BIG THUNDERBOLT 2

Бренд: LaCie Страницы: 20

Бренд: Lifetime Страницы: 40

Бренд: Seagate Страницы: 86

Бренд: Western Digital Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды