Supermicro SuperServer E403-9D-14CN-FRDN13+ Скачать руководство пользователя страница 19

Страница: 19 / 136

Chapter 2: Maintenance and Component Installation

Chapter 2

Maintenance and Component Installation

Note: Maintenance and component installation must be carried out by SUPERMICO
service personnel only. Please ensure that the device is connected to a socket/outlet
that has a ground/earth connection.

This chapter provides instructions on installing and replacing main system components. To

prevent compatibility issues, only use components that match the specifications and/or part

numbers given.

Installation or replacement of most components require that power first be removed from the

system. Please follow the procedures given in each section.

2.1 Removing Power

Use the following procedure to ensure that power has been removed from the system.

1. Use the operating system to power down the system.

2. After the system has completely shut down, disconnect the power cord from the power

source.

3. Disconnect the power cord from the chassis.

Содержание SuperServer E403-9D-14CN-FRDN13+









































































































































Результаты поиска

Содержание SuperServer E403-9D-14CN-FRDN13+

Отзывы:

Бренды по названию

Популярные бренды

Supermicro SuperServer E403-9D-14CN-FRDN13+, Руководство пользователя

Результаты поиска

Содержание SuperServer E403-9D-14CN-FRDN13+

Отзывы:

Бренды по названию

Популярные бренды