Supermicro SuperBlade SBI-6419P-C3N Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 97

background image

1-3

Chapter 1: Introduction

Please refer to the Supermicro website for a list of supported memory
(

www.supermicro.com/products/superblade

). The detailed specifications for a blade

module will contain a link to a list of recommended memory sizes and manufacturers.

Details on installation of memory modules into the SBI-6419P-C3N SuperBlade module
are found in

Chapter 3: "Setup and Installation" on page 3-1

Storage

The SBI-6419P-C3N SuperBlade module has three HDDs in front-mounted easily
removable hot-swap carriers. These can either be configured for two NVMe and one
SAS3/SATA3 2.5" drives or three SAS3/SATA3 2.5" drives.

Chapter 3: "Setup and Installation" on page 3-1

for storage installation details.

RAID

Each SBI-6419P-C3N blade module supports several hard drives, which may create a
RAID system for the blade module. The SBI-6419P-C3N has a Broadcom 3108 SAS
RAID chip for RAID 0, 1, and 5.

Further information on the RAID and its software can be found on our website at:

http://www.supermicro.com/manuals/other/
LSI_2108_2208_SAS_MegaRAID_Configuration_Utility.pdf

Enclosure Requirements

The SBI-6419P-C3N blade module requires one of the following enclosures to run in:

•

SBE-614E-822

•

SBE-614E-622

•

SBE-614E-422

•

SBE-614EB-422

The SBI-6419P-C3N blade module also requires a power supply in the enclosure to run
the blade module. Available SuperBlade power supplies can be found on the
Supermicro website at

42https://www.supermicro.com/products/SuperBlade/

.

Density

A maximum of 14 SBI-6419P-C3N blade modules may be installed into a single blade
enclosure. Each blade enclosure is a 6U form factor, so a standard 42U rack may
accommodate up to seven enclosures with 98 blade modules, or the equivalent of 98 1U
servers. With the inclusion of seven CMM modules and fourteen 1G/25G Ethernet
switches, this would occupy up to 119U space in a conventional 1U server configuration.

«
...
9
10
11
12
13
...
»

Содержание SuperBlade SBI-6419P-C3N


































































































Отзывы:

Нет отзывов

Похожие инструкции для SuperBlade SBI-6419P-C3N

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: C&K systems Страницы: 2

Бренд: T-Verter Страницы: 121

Бренд: Happy Страницы: 10

Бренд: tams elektronik Страницы: 60

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

Бренд: halstrup-walcher Страницы: 39

iBox Hub 25020180

Бренд: Hans Grohe Страницы: 36

Бренд: NAD Страницы: 4

Бренд: NAD Страницы: 4

Бренд: Zeta Страницы: 44

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Бренд: Advantech Страницы: 2

Vizia RF+ VRP15-1LW

Бренд: Leviton Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды