Supermicro 6048R-E1CR24L Скачать руководство пользователя

Страница: 133 / 142

Chapter 7: BIOS

7-45

7-7 Boot Settings

This submenu allows the user to configure Boot settings for this system:

Boot Configuration

Boot Mode Select

Use this item to select the type of device to be used for system boot. The options
are Legacy, UEFI, and

Dual.

Fixed Boot Order Priorities

This option prioritizes the order of bootable devices from which the system will boot.
Press <Enter> on each entry from top to bottom to select devices.
When the item above -"Boot Mode Select" is set to

Dual

(default), the following

items will be displayed for configuration:

•

Boot Option #1 - Boot Option #15

When the item above -"Boot Mode Select" is set to Legacy, the following items will

be display for configuration:

•

Boot Option #1 - Boot Option #7

When the item above -"Boot Mode Select" is set to UEFI, the following items will

be display for configuration:

•

Boot Option #1 - Boot Option #8



Delete Boot Option

Use this item to select a boot device to delete from the boot priority list.

Содержание 6048R-E1CR24L















































































































































Результаты поиска

Содержание 6048R-E1CR24L

Отзывы:

Похожие инструкции для 6048R-E1CR24L

Бренды по названию

Популярные бренды

Supermicro 6048R-E1CR24L, Руководство пользователя

Результаты поиска

Содержание 6048R-E1CR24L

Отзывы:

Похожие инструкции для 6048R-E1CR24L

Бренды по названию

Популярные бренды