INNOVATIVE HEARTH PRODUCTS • POWER VENT DV GAS FIREPLACES (DRT63__TYN / DRC63__TYN) • CARE AND OPERATION INSTRUCTIONS
13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
WARNING
Any safety screen or guard
removed for servicing the appli-
ance must be replaced prior to
operating the appliance.
AVERTISSEMENT
Tout écran ou protecteur retiré
pour permettre l’entretien de
l’appareil doit être remis en
place avant de mettre l’appareil
en marche.
WARNING
Do not operate appliance with
the glass front removed, cracked
or broken.
Front Glass Enclosure Panel Removal
and Installation
To install the front glass door assembly,
proceed as follows:
1.
Retrieve the glass door assembly. Visually
inspect the gasket on the backside of the
panel. The gasket surface must be clean,
free of irregularities and seated firmly.
2.
Position the door frame in front of the firebox
opening and engage the bottom flange over
the rail at the bottom of the firebox opening.
3.
Swing the door up and back. Ensure the
gasket seats evenly as the door draws shut.
Engage the nut insert and fasten with two
screws to secure the door.
4.
Install the door modesty shield on top flange
glass door as follows: grab the door modesty
shield with both hands, with the open hem
going down and engage it with the upper lip
of the glass door frame by pushing it all the
way down. Make sure the installed shield is
firmly in place.
5.
With the firescreen hanging on the screen rod,
drop in the right side of the rod to the right
modesty panel. Then drop in the left side of
the rod through the slot of the left modesty
panel. Make sure that the rod is supported
by the bracket in the center of the fireplace.
WHEN INSTALLING THE GLASS DOOR,
SECURELY TIGHTEN THE LATCH SCREWS
- SEE THE FIRST WARNING ON THIS PAGE.
When installing the glass door, ensure the
spacing on both sides are equal.
Figure 9 - Front Glass Enclosure
Panel
Top Flange Glass Door
Frame Assembly
Glass Door Latch (2)
Latch
Screws
Firebox Floor
Glass Door Assembly
WARNING
• When reinstalling the glass
door, the door latch screws
must be securely tightened
to prevent the glass door
from falling out, which could
potentially cause damage and
possible injury.
• Do not attempt to substitute the
materials used on this door,
or replace cracked or broken
glass.
• Handle this glass with extreme
care! Glass is susceptible to
damage - Do not scratch or
handle roughly while reinstall-
ing the glass door frame.
• The glass door of this appli-
ance must only be replaced
as a complete unit as provided
by the manufacturer. Do not
attempt to replace broken,
cracked or chipped glass sepa-
rately.
• Do not attempt to touch the
front enclosure glass with your
hands while the fireplace is in
use.
AVERTISSEMENT
Ne pas utiliser l'appareil si le
panneau frontal en verre n'est
pas en place, est craqué ou
brisé.
Only doors certified with the appliance
shall be used.
Seules des portes certifiées pour cet
appareil doivent être utilisées.
WARNING: DO NOT abuse glass door by
striking or slamming shut.
These are direct-vent appliances. They are
designed to operate only when the front glass
enclosure panel is installed. Generally the front
glass enclosure panel should not be removed
except to gain access to the components within
the firebox.
Removing Glass Enclosure Panel
(see
Figure 9)
To remove the firescreens, lift up the center of
the rod to disengage it from the center bracket,
bend down at center, hold left side with hand
until it disengages from left side, being careful
not to scratch paint. Slowly remove the rod
from the right side.
Remove the door modesty shield from the top
flange glass door by pulling it up firmly with
both hands until it is disengaged. Using a phillips
screwdriver, unfasten two (2) screws located
at the top of the glass frame.
Tilt the glass frame at the top away from the
unit. Lift it carefully off the bottom door track
and set the door aside, protecting it from
inadvertent damage.
