background image

24

25

1

+

direct to function 

selection wheel:

on/off -

bromicharge -

boost level -

maintenance -

status and messages

mode selection 

wheel:

in.clear icon

sanitization mode

(only available if the system detects a connected in.clear water sanitization system)

To select the sanitization mode, slide the left wheel up or down until the in.clear icon menu is 

highlighted in the middle.
In the sanitization page you can access the following:
• in.clear on/off  

• boost level 

• bromicharge  

• maintenance level

To select an item, slide the right wheel until the desired icon is highlighted in the middle.

on/off

bromicharge™ level

turn in.clear ON - 

Step 1 (icon red)

Slide the right wheel until the power on/off icon is 

highlighted in the middle. Press the icon to turn 

in.clear on.

turn in.clear OFF - 

Step 2 (icon yellow)

Press icon for 5 seconds to confirm power off.

To perform a water test, slide the right wheel until 

the add BromiCharge™ icon is highlighted in the 

middle. 
There is no need to add sodium bromide if the 

indicator is in the green zone.
When adding sodium bromide, the gauge 

indicator will gradually shift to the right. When 

adding clean water to the spa, the indicator will 

shift to the left.
In order to achieve the proper level, start pumps 

and add 227g (.5 lb) of BromiCharge™ at a time 

and always allow 5 minutes for the gauge to react 

before adding more sodium bromide.

When performing a test, the BromiCharge™ 

gauge indicates the approximate sodium bromide 

level of the spa water. 

The green zone in the center area of the gauge 

should be targeted for optimal performance.

turn in.clear OFF -  

Step 3 (icon green)

Press the icon to turn off the in.clear.

1

+

boost level

maintenance level

Use a test kit to check the bromine level. It should 

be between 3-5 ppm. If the bromine level stays 

within that range for 3 consecutive days, your 

maintenance level is well adjusted.

modify the boost level

Boost mode is activated automatically 5 minutes 

after starting a pump. Boost mode increases 

the bromine generation rate to keep the water 

clear, clean and soft. As a rule of thumb, its level 

correspond to the number of bathers.
To modify the boost level, slide the right wheel 

until the boost icon is highlighted in the middle 

and use the up or down arrow keys to adjust the 

level.
Click on the the level icon to confirm your 

selection.

modify the maintenance level

To verify or modify the maintenance level, slide 

the right wheel until the maintenance icon is 

highlighted in the middle.
The recommended maintenance level is 12.
Use the up or down arrow keys to adjust the level.
Note that the level can be adjusted by increment 

of 2 using the up and down arrow keys.

Please note that it is not recommended to change 

the maintenance level at steps greater than 2.  

A confirmation will be asked by the system if  

you do.
If you do, retest the bromine level the day after.  

If the bromine is not in the 3-5 range and is 

higher than 5 ppm, decrease the maintenance 

level. If the bromine is lower than 3 ppm, increase 

it. Repeat until the test reads a bromine level in 

the 3-5 range.

Содержание Control in.k1000





















Отзывы: