background image

www.SuperiorFireplaces.US.com

126601-01A

15

 CAUTION: All gas piping 

and connections must be tested 

for  leaks  after  the  installation 

is completed. After ensuring 

that the gas valve is on, apply 

soap  and  water  solution  to  all 

connections and joints. Bubbles 

forming  show  a  leak.  Correct 

all leaks at once. DO NOT USE 

AN  OPEN  FLAME  FOR  LEAK 

TESTING AND DO NOT OPER-

ATE ANY APPLIANCE IF A LEAK 

IS DETECTED. LEAK TESTING 

SHOULD BE DONE BY A QUALI-

FIED SERVICE PERSON.

 WARNING: Do not operate an 

unvented gas log set in this fire-

place with the chimney removed.

A gas line or gas log lighter may be installed 

for the purpose of installing a vented or vent-

free decorative gas appliance incorporating an 

automatic shutoff device and complying with 

the S

tandard for Decorative Gas Appliances for 

Installation in Vented Fireplaces, ANSI Z21.60

 

or 

American Gas Association draft requirements 

for Gas Fired Log Lighters for Wood Burning 

Fireplaces, Draft NO. 4

 dated August, 1993.

OPTIONAL GAS LINE INSTALLATION 

Continued

If  you  install  a  decorative  gas  appliance 

(vented gas log), the decorative gas appliance 

must comply with the 

Standard for Decorative 

Gas Appliance for Installation in Solid Fuel 

Burning  Fireplaces, ANS  Z21.60  or  Z21.84 

and shall also be installed in accordance with 

the 

National Fuel Gas Code, ANSI  7223NFPA 

54 latest edition

.

If you wish to install an unvented (vent-free) 

gas log set, only unvented gas log sets which 

have been found to comply with the standard 

for unvented room heaters, ANSI Z21.11.2 are 

to be installed in this fireplace.

  WARNING:  If  the  fireplace 

has been used for wood burning, 

the firebox and chimney must be 

cleaned of soot, creosote and 

ashes  be  a  qualified  chimney 

cleaner.  Creosote  will  ignite  if 

heavily heated.

 WARNING: When using a 

decorative vented gas log, the 

damper must be removed or 

permanently locked in the fully 

open position and the glass doors 

must be in the fully open position.

GLASS DOOR INSTALLATION

IMPORTANT: Install glass door 

frame before installing glass door.

INSTALLING DOOR FRAMES

1.  Remove screws from smoke shelf (see 

Figure 26).

2.  Mount  top  door  frame  and  secure  with 

screws removed in step 1.

3.  Remove center ash refractory by pulling 

ring handle (see Figure 27, page 16).

4.  Remove ash box.
5.  Remove three screws located at front of 

firebox (see Figure 27, page 16).

Figure 26 - Installing Top Door Frame

Top Door Frame

Smoke Shelf

Содержание WRT4536RH





























Отзывы: