background image

SuperiorFireplaces.us.com

900467-01B

15

OPERATION

9.  Slightly push in and turn control knob counterclockwise 

 

to the ON position.

10.Wait one minute and move switch to the ON position to 

light burner.

 

NOTE

: AUTO is only functional when using optional remote 

control accessory.

11. Set flame adjustment knob to any level between HI and LO.

FOR YOUR SAFETY 

READ BEFORE LIGHTING

 

WARNING: If you do not follow these instruc

-

tions exactly, a fire or explosion may result 

causing property damage, personal injury or 

loss of life.

A. This appliance has a pilot which must be lighted with 

a piezo igniter. When lightning the pilot, follow these 

instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area 

for gas. Be sure to smell next to the floor because some 

gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do  not  touch  any  electric  switch;  do  not  use  any 

phone in your building.

• Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire 

department.

C.  Use only your hand to push in or turn gas control knob. 

Never use tools. If the knob will not push in or turn by 

hand, do not try to repair it, call a qualified technician. 

Force or attempted repair may result in a fire.

D. Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect 

the appliance and to replace any part of the control sys-

tem and any gas control which has been under water.

LIGHTING

 

 INSTRUCTIONS

1.  STOP! Read the safety information, above.
2.  Make sure switch is in the OFF position. 
3.  Be sure gas line shut-off valve is OPEN.
4.  Press in and turn control knob clockwise 

 to the 

OFF position 

(see 

Figure 26

)

.

 

NOTE

: Knob cannot be turned from PILOT to OFF unless 

knob is pushed in slightly. DO NOT FORCE.

5.  Wait five (5) minutes to clear out any gas. If you then smell 

gas, STOP! Follow "B" in the safety information in column 

1. If you don't smell gas, go on the next step.

6. Press in and turn control knob counterclockwise 

 

to the PILOT position. Press in control knob for five (5) 

seconds 

(see 

Figure 26

)

.

7. With control knob pressed in, press and release igniter 

button. This will light pilot. If needed, keep pressing igniter 

button until pilot lights.

 

NOTE

: If pilot does not stay lit, contact a qualified service 

person or gas supplier for repairs.

8.  Keep control knob pressed in for 30 seconds after lighting 

pilot. After 30 seconds, release control knob.

• If control knob does not pop out when released, turn off 

gas supply and contact a qualified service person or gas 

supplier for repairs.

 

NOTE

: If pilot goes out, repeat steps 4 through 8.

TO TURN OFF GAS 

TO APPLIANCE

1.  Turn control knob clockwise 

 to the OFF position.

2a.Set switch in the OFF position.

2b.

If Using Optional Hand-Held Remote: 

Set selector switch 

in the OFF position to prevent draining battery. 

3.  Close equipment shutoff valve 

(see 

Figure 13, Page 9

)

.

MANUAL LIGHTING

 

PROCEDURE

1.  Follow steps 1 through 6 under 

Lighting Instructions

.

2.  Press control knob and light pilot with match. 

3.  Keep control knob pressed in for 30 seconds after light-

ing pilot. After 30 seconds, release control knob. Now 

follow steps 9 through 11, under 

Lighting Instructions

.

OPTIONAL HAND-HELD

 

REMOTE OPERATION

NOTE

: All  remote  control  accessories  must  be  purchased 

separately (see Accessories, 

Page 23

). Follow instructions 

included with the remote control.

NOTICE: You must light the pilot before using 

the hand-held remote control unit. See 

Lighting 

Instructions

.

After lighting, let pilot flame burn for about one minute. Turn 

control knob to ON position. Adjust flame adjustment knob 

anywhere between HI and LO. Slide the selector switch to 

the REMOTE position

 (see 

Figure 26

). 

Figure 26 - Control Knob, Igniter Button and Remote 

Selector Switch

Selector 

Switch 

Control 

Knob in OFF 

Position 

Flame Adjustment 

Knob 

Igniter

NOTE

: The burner may light if hand-held remote was on when 

selector switch was last turned off. You can now turn burner 

on and off with hand-held remote control unit.

 

IMPORTANT

Do not leave selector switch in the REMOTE 

or ON position when pilot is not lit. This will drain the battery.

f i r e - p a r t s . c o m

Содержание LMF30GT































Отзывы: