Instructional Sheet
Part Number:
4400 Earth City Expy, St. Louis MO 63045
866-590-3533 [email protected]
ALKW8-RGB72
Important: Read all instructions prior to installation.
Diagram 1
Remote Battery Replacement
Remote Functions
1. Remove three philips head screws and remove the button panel.
2. Carefully remove battery and replace with new.
3. Reposition button panel then insert and tighten screws
1.
Connect strips to Splitter Cable then connect to Controller. Temporarily apply
power to the controller and test strip locations for proper lighting effect.
2.
Mark the desired location of the strips. Mount strips using double sided tape
or silicone in desired location and away from heat sources and moving parts.
3.
Mount controller and connection box in dry locations away from heat sources
and moving parts and route power wires to power source then connect. Route
white antenna wire away from metal objects for maximum operating range.
Multi Color 8 Piece Accent Light Kit
2 - 5” Waterproof Accent Light Strips
4 - 6.75” Waterproof Accent Light Strips
2 - 8.75” Waterproof Accent Light Strips
1 - RF RGB Accent Light Controller
1 - RF Wireless Key Chain Remote (RCW-RFR)
1 - Splitter Cable
1 -12V 27A Battery
Parts Included
Installation
Specifications
RGB LED Flexible Light Strip
Battery
1/4” Snap Spades
8-Way Splitter
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
Power Supply
OR
CPS connector
(CPS-F2ST)
(CPS-12VDC-50W)
Fuse 3A
RGB LED Flexible Light Strip
8-Way Splitter
White
Antenna
Blue
Brake
Override
To Brake
Switch
Controller
RGB RF
Black
Ground
Red
Power In
Blue
Wire
Running Light Cicuit (+)
Ground
White
Antenna
PSC-164
Brake Light
Circuit (+)
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
V+
G
R
B
Controller
RGB RF
Input Voltage
9~14.8 VDC
Controller Output Current
3 x 1A Maximum
Fuse Size
3A
Operating Temperature
-4 ~122° F (-20~50° C)
Strip IP Rating
Waterproof IP67
Static Color Dynamic Modes
2
Seven Color Dynamic Modes
2
Static Colors
18
Override Mode
1
Brightness Levels
5
Remote Battery
12V 27A x 1
Remote Range
33 Feet (10m) Maximum
Remote Frequency
315 MHz
FCC ID
2AFXS-JX-R001
Warranty
2 Years
Remote comes paired to the controller. Use the following procedure if additional
remotes are required.On power up, LEDs will be green indicating pairing mode
for three seconds. During green pairing mode, press button “A” then “B” to pair a
new remote.
Remote Pairing
Wiring
Output Connector
Polarity
Purpose
Black
Positive (+)
Common Anode
Red
Negative (-)
Red LED Cathode
Green
Negative (-)
Green LED Cathode
Blue
Negative (-)
Blue LED Cathode
Input Wires
Polarity
Purpose
Black
Negative (-)
Ground In (-)
Red
Positive (+)
9~14.8 VDC Power In (+)
Blue (see below)
Positive (+)
9~14.8 VDC Red Override Signal In (+)
Blue wire activates red single color mode at full brightness while voltage is applied.
Use for brake override if required. Works as brake override even when controller is
in standby mode.
Button
Functions
Cycles up through 18 single color modes and two 7 color modes.
Press and hold for dimming 80%, 60%, 40%, 20% and back to
100% during single color modes.
Activates Flash Modes during single color modes. Switches
between Flash/Flash/Long Pause and Flash/Flash/Short Pause
during flash modes. Increases cycle speed during 7 color modes
Activates Fading Mode during single color modes. Decreases
cycle speed during 7 color modes.
On/Off
Hold for 6 seconds to return to Mode 1 (Static Red)
RCW-RFR
Slide Cover
