Superabrasive Lavina 32G -X Скачать руководство пользователя страница 43

Superabrasive 

Owner’s Manual Original Language – Lavina 

®

32G-X/GTX  

7/2019 

 

43

 

 

12.EMISSION CONTROL WARRANTY STATEMENT 

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS 
The  California  Air  Resources  Board  and  Superabrasive  Inc.  are  pleased  to  explain  the  emissions  control  system 
warranty on your 2016 small off-road engine (SORE). In California, new SORE must be designed, built and equipped to 
meet the State’s stringent anti-smog standards. Superabrasive Inc. must warrant the emission control system on your 
SORE for the period of time listed below provided there has been no abuse, neglect or improper maintenance of your 
SORE. 
Your  emission  control  system  may  include  parts  such  as  the  carburetor,  fuel-injection  system,  the  ignition  system, 
catalytic converter, fuel tanks, fuel lines, fuel caps, valves, canisters, filters, vapor hoses, clamps, connectors, and other 
associated emission-related components. 
Where a warrantable condition exists, Superabrasive Inc. will repair your SORE at no cost to you including diagnosis, 
parts and labor. 
MANUFACTURER'S WARRANTY COVERAGE 
The emission control system is warranted for 2 years. If any emission-related part on your equipment is defective, the 
part will be repaired or replaced by Superabrasive Inc. 
OWNER'S WARRANTY RESPONSIBILITIES 
As the small off-road engine (SORE) owner, you are responsible for the performance of the required maintenance listed 
in  your  owner's  manual.  Superabrasive  Inc.  recommends  that  you  retain  all  receipts  covering  maintenance  of  your 
SORE engine, but Superabrasive Inc. cannot deny warranty solely for the lack of receipts or for your failure to ensure 
the performance of all scheduled maintenance. 
As the SORE owner you should however be aware that Superabrasive Inc. may deny your warranty if your SORE or its 
part has failed due to abuse, neglect, improper maintenance or unapproved modification. 
You are responsible for presenting your utility equipment engine to a Superabrasive Inc. distribution center as soon as 
the  problem  exists.  The  warranty  repairs  should  be  completed  within  a  reasonable  amount  of  time,  not  to  exceed  30 
days. If you have any questions regarding your warranty rights and responsibilities, you should contact Superabrasive 
Inc. at 1-(800)-987-8403 or by e-mail at [email protected] 
Superabrasive Inc 
9411 Jackson trail Rd  
Hoschton, GA 
USA, 30548 
 
GENERAL EMISSIONS WARRANTY COVERAGE 
Superabrasive Inc. warrants to the ultimate purchaser and each subsequent purchaser that the equipment is:  
Designed, built and equipped so as to conform with all applicable regulations; and 
Free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material 
respects to that part as described in Superabrasive Inc. application for certification. 
The warranty period begins on the date the equipment is delivered to an ultimate purchaser or first placed into service. 
The warranty period is two years. 
Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows: 
 
 (1)Any  warranted  part  that  is  not  scheduled  for  replacement  as  required  maintenance  in  the  written  instructions 
supplied, is warranted for the warranty period stated above. If the part fails during the period of warranty coverage, the 
part  will  be  repaired  or  replaced  by  Superabrasive  Inc.  according  to  subsection  (4)  below.  Any  such  part  repaired  or 
replaced under warranty will be warranted for the remainder of the period. 
(2)Any  warranted part that is scheduled only for regular inspection in the  written instructions supplied  is warranted for 
the warranty period stated above. Any such part repaired or replaced under warranty will be warranted for the remaining 
warranty period. 
(3)Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is 
warranted for the period of time before the first scheduled replacement date for that part. If the part fails before the first 
scheduled replacement, the part will be repaired or replaced by Superabrasive Inc. according to subsection (4) below. 
Any  such  part  repaired  or  replaced  under  warranty  will  be  warranted  for  the  remainder  of  the  period  prior  to  the  first 
scheduled replacement point for the part. 
(4)Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty 
station at no charge to the owner. 
(5)Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers 
that are franchised to service the subject engines or equipment. 
(6)The  SORE  owner  will  not  be  charged  for  diagnostic  labor  that  is  directly  associated  with  diagnosis  of  a  defective, 
emission-related warranted part, provided that such diagnostic work is performed at a warranty station. 
(7)Superabrasive Inc. is liable for damages to other engine or equipment components proximately caused by a failure 
under warranty of any warranted part. 
(8)Throughout  the  SORE  warranty  period  stated  above,  Superabrasive  Inc.  will  maintain  a  supply  of  warranted  parts 
sufficient to meet the expected demand for such parts. 

Содержание Lavina 32G -X













































Отзывы: