EXTERNAL TEACHING FUNCTION
14
This product incorporates the external teaching function. Take care that
the teaching methods for mark mode and color mode differ in the
external teaching function.
<2-level teaching>
Align the beam spot to the mark to be detected in 'RUN
mode'.
Input the external signal for 20ms or more in step
state.
(Do not input the external signal more than 2 sec. continuously.)
Align the beam spot to the base (non-mark area), and input
the external signal for 20ms or more.
COLOR
In case of mark mode
COLOR
COLOR
SUNX Limited
Connector type / LX-101
غ
-Z
٨
Sensor mounting bracket / MS-LX-1 (optional)
٨
Sensor mounting bracket / MS-LX-2 (optional)
57
25
r
0.1
5
47
r
0.1
25
r
0.1
5
47
r
0.1
57
72
15
30
40
45
28
r
0.1
39
t3
t3
27
15
2-M5
0.8
4-M4
0.7
2-R5
2-R5
4-R2
15
10
80
2-M4
0.7
60
25
r
0.1
3-R2
2-R5
R2
5.2
47
r
0.1
5
4
6
57
3-M5
0.8
41
20
4
6
30.4
4.5
2-R4.7
R4.7
R2
21
r
0.1
9
28
r
0.1
24
27.2
t3
9.4
Ǿ
14.4
3
5
M12
5
47
57
71.5
15
Ǿ
22
25
35
1.5
24
<Full-auto teaching>
or
COLOR
COLOR
Put the object on the assembly line at 'RUN mode' state.
COLOR
(Timing chart)
2sec. or more
Start sampling
ON
OFF
When the external signal is input for 2 sec. or more, sampling
begins. When sampling finishes, the digital display flashes. If
'
' is displayed, slow down the line speed, and carry out
the teaching again.
<1-level teaching>
Align the beam spot to the mark to be detected in 'RUN
mode'.
Input the external signal for 20ms or more in step
state.
In case of color mode
(Timing chart)
OUTPUT 2 (INVERSION OUTPUT) (OUT) (For LX-101
غ
type only)
The LX-101
غ
cable type incorporates the output 2 (inversion output)(OUT).
For teaching, this function is convenient for inverting logic of LIGHT-ON /
DARK-ON (mark-mode), and coincidence-ON / incoincidence-ON (color mode).
When the output 2 is used, connect the output wire (output 2) to +V side
(0V side for PNP output type). When the output 2 is not used, be sure to
insulate it.
15
COLOR
20ms or more
ON
OFF
COLOR
When the full-auto teaching is used, the output operation is set to 'DARK-ON'.
Note:
ERROR DISPLAY
16
٨
Take measurment for the error as shown below:
Remedy
Turn off the power supply and check the
load.
Shorten the load and flows overcurrent.
Display
Error content
17
DIMENSIONS (Unit: mm)
Cable type / LX-101
غ
15
2-
Ǿ
4.5
(mounting hole)
Ǿ
22
3
5
5
47
57
25
35
1.5
24
(Timing chart)
ON
OFF
20ms or more
20ms or more
S p a c e
1.5 sec
or more
Input external signal
aligning beam spot to
mark
Input external signal aligning
beam spot to base (non-mark
area)
2-
Ǿ
4.5
(mounting hole)
