background image

                                                            OPERATION & MAINTENANCE MANUAL              SWE215F

 

                                                                                                                                                                                   

118 

 

Fuel may congeal depending on the temperature when it is used (particularly in low temperature below 

-15°C

5°F

. It’s necessary to use the fuel that is suitable for the temperature. 

 

To  prevent  humidity  in  air  to  condense  in  fuel  tank  to  form  water,  top  up  oil  tank  after  the  work  is 

finished every day. 

 

Before  starting  the  engine,  or  when  10  minutes  have  passed  after  adding  fuel,  drain  the  sediment  and 

water from the fuel tank. 

 

If there runs out of fuel, or if the filters have been replaced, it is necessary to exhaust the air from the oil 

circuit. 

 

4.2.3 Coolant in Cooling System   

 

River water contains large amount of calcium and other impurities, so if it is used, scale will stick to the 

engine and radiator, and this will cause defective heat exchange and overheating. 

 

When using antifreeze, always observe the precautions given in the Operation and Maintenance Manual. 

 

Antifreeze is flammable, so be extremely careful not to expose it to flame or fire. 

 

The proportion of anti-freeze to water differs according to the ambient temperature. 

For details of the mixing proportions. 

 

If engine is overheated, before adding coolant, wait for the engine to cool down. 

 

If the coolant level is low, it will cause overheating and will also cause problems with corrosion from the 

air in the coolant. 

 

4.2.4 Grease   

 

Grease is used to prevent twisting and noise at the joints.   

 

If any part becomes stiff after being used for long time, add grease. 

 

Always wipe off all of the old grease that is pushed out when greasing. Be particularly careful to wipe 

off the old grease in  places  where  sand or  dirt  sticking  in  the grease  would cause wear  of  the  rotating 

parts.   

 

4.2.5 Oil and Fuel Storage   

 

Keep indoors preventing any water, dirt, or other impurities from getting in. if drums have to be stored 

outside, cover them with a waterproof sheet or take other measures to protect them.   

 

When keeping drum cans for a long period, put the drum on its side so that the filler port of the drums is 

at the side to prevent moisture from being sucked in.   

 

To prevent any change in quality during long-term storage. Be sure to use in the order of first in- first 

out (use the oldest oil or fuel first). 

 

Содержание SWE215F-5























































































































































































Отзывы: