manualshive.com logo in svg

SunStar KM-380BL, Руководство пользователя

Поделиться
Скачать
SunStar KM-380BL Скачать руководство пользователя страница 5

1-1) Machine

mobilization

Danger

1-2) Machine

Installation

Caution

1-3) Troubleshooting

Danger

If in need of troubleshooting, call a trained A/S engineer who has been educated by
Sunstar. 

ⓐ

Be sure to turn the power off before cleaning and repair.  And wait for about 4 minutes until

the machine discharges completely. 

ⓑ

Part of or the entire machine should not be modified without any consultation with our

company.  Such modification could threaten the safety in operating the machine.

ⓒ

In case of repair, change the damaged part into the genuine part of our company 

ⓓ

After repair, cover the machine with the safety cover that was removed for repair.

Only personnel with a full understanding of the safety rules should move the
machine. The following directions must be observed when transferring the machine.  

ⓐ

At least 2 persons should move the machine together.

ⓑ

In case the machine should be transported, wipe the oil covered on the machine to prevent

accidents.

Because physical damages such as the machine’s dysfunction and breakdown are
likely to occur depending on the environment in which the machine is installed, the
following preconditions must be met. 

ⓐ

Please unpack the machine package in order from the upper side.  Be particularly careful

of the nails in the wooden box. 

ⓑ

Because machines are apt to be contaminated and corroded by dust and moisture, install a

climate controller and clean the machines regularly.

ⓒ

Keep the machine out of direct rays of the sun. 

ⓓ

Keep both sides and the backside of the machines at least 50cm from the wall to secure

enough space for repair. 

ⓔ

Don’t run the machine near places with any danger of explosion.

Don’t run the machine near places with any danger of explosion, including places where
sprays like aerosol are used in large quantities or oxygen are dealt with, unless the exact
actions concerning the operation are guaranteed to avoid the explosion. 

ⓕ

Illuminators do not come equipped with the machine due to the machine’s characteristics.

So, users should install the lighting apparatus around the working area.

[Note] The details about the installment of the machine are described in “2.

Installation”. 

5

Содержание KM-380BL

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды