SunStar KM-250 Series страница 5 Скачать руководство пользователя

Страница: 5 / 31

1-1) Machine

mobilization

Danger

1-2) Machine

installation

Caution

1-3) Troubleshooting

Danger

When the machine is in need of repair, only our authorized service technicians must

handle it.

ⓐ

Before cleaning and repairing the machine, shut off the power supply and wait four

minutes for the machine to discharge completely.

ⓑ

No part of the machine or specifications may be modified without prior consultation

with our company. Any such modification could risk safe operation of the machine.

ⓒ

In case of repair, replace only with standard OEM parts from SunStar.

ⓓ

After repair, put safety covers back on the machine.

Only personnel with a full understanding of the safety rules should move the machines.

The following directions must be observed when delivering the machines.

ⓐ

At least two or more people should move the machine.

ⓑ

Before delivering the machine, thoroughly wipe off the oil on the machine to

prevent accidents.

Physical damages such as functional difficulties or breakdowns may occur

depending on installation conditions of the machines. Be sure to heed the following

conditions.

ⓐ

Remove the packing from top to bottom. Watch out for nails on the wooden box.

ⓑ

Install a climate controller and clean it regularly to prevent dust and moisture build-

up from contaminating and corroding the machines.

ⓒ

Keep the machines away from direct sunlight.

ⓓ

Keep a minimum distance of 50cm between the machine at both sides and

backside and the wall to secure sufficient space for repair.

ⓔ

Do not operate the machine near areas with danger of explosion. Refrain from

running the machine in the vicinity of risky places, e.g., where a large quantity of

aerosol-spraying products or oxygen are handled, unless specific guarantees are

given otherwise for the operation of the machine to prevent explosion at such

places.

ⓕ

The user should install an illuminator in the work area for the machine does not

come supplied with any lighting apparatus due to the specific features of the

machine.

[Note] Details of the machine installation are laid out in No. 2 Installation.

Keystone Sewing Machine Company, Inc.

Содержание KM-250 Series
































Результаты поиска

Содержание KM-250 Series

Отзывы:

Похожие инструкции для KM-250 Series

Бренды по названию

Популярные бренды

SunStar KM-250 Series, Руководство пользователя

Результаты поиска

Содержание KM-250 Series

Отзывы:

Похожие инструкции для KM-250 Series

Бренды по названию

Популярные бренды