SunStar KM-2070P Скачать руководство пользователя страница 13

Страница: 13 / 41

[ Fig. 5 ]

F. After connecting V belt, fully unfasten the fixing nut

①

②

to up and down, tension occurs to belt by self weight of
motor

③

. On this condition, fasten the fixing nut

①

first

and the fixing nut

②

tightly.

[ Fig. 6 ]

A. Insert the presser foot lifter pad (group)

①

packed in the

accessory box into control body shaft

②

of oil fan.

B. After unfastening the volt

③

and deciding the location

convenient of operation for presser foot lifter, tightly
fasten again.

4) Installation of Presser Foot Lifter Pad

③

②

①

[ Fig. 7 ]

A. Put down the feed dog lower than top of the needle plate

by turning the pulley.

B. Put down the presser foot

②

to presser bar lifter

①

C. Unfasten nut

③

D. Adjust by turning the joint screw

⑥

that operation olume

(space) of control body

⑤

should become about 2mm

when lightly press the presser foot lifter pad (group)

④

hands.

E. After adjustment, joint the nut

③

tightly.

F. Unfasten the nut

⑦

G. Adjust by rotating joint screw

⑧

that joint screw

⑧

becomes about 7mm higher than control body

⑤

H. Adjust by turning joint screw

⑧

that presser foot

②

becomes within 10mm than needle plate when hardly
pressed the presser foot lifter pad (group)

④

I. After adjustment, joint the nut

⑦

tightly.

①

②

④

③

⑥

⑤

⑧

⑦

5) Adjustment of Presser Foot Lifter (group) Pad

①

②

④

③

Содержание KM-2070P










































Результаты поиска

Содержание KM-2070P

Отзывы:

Похожие инструкции для KM-2070P

Бренды по названию

Популярные бренды

SunStar KM-2070P, Руководство пользователя

Результаты поиска

Содержание KM-2070P

Отзывы:

Похожие инструкции для KM-2070P

Бренды по названию

Популярные бренды