background image

14

BREEZY STYLE

ENGLISH

Brake lever Extension

 

The extension for the brake lever 

can be removed or folded down. 

The longer lever helps to minimise 

the effort needed to set the wheel 

locks (Fig.7.0).

 CAUTION!

Mounting the wheel lock too 
close towards the wheel will 
result in a higher effort to 
operate. This might cause the brake lever extension to break!

 CAUTION!

Leaning onto the brake lever extension while transferring will 
cause the lever to break! Splashing water from tyres might 
cause the wheel lock to malfunction.

Options - Brakes

Drum Brakes

Drum brakes permit safe and 

convenient braking for an attendant. 

They can also be set with the aid of 

a locking lever (1) to prevent rolling. 

The lever must snap audibly into 

place. Drum brakes are not 

influenced by air pressure inside the 

tyres. Your wheelchair cannot be 

moved when the drum brakes are 

set (Fig. 7.0).

 CAUTION!

Drum brakes must only be adjusted by authorised dealers.

Wheel locks 

Your wheelchair is equipped with two wheel locks. They are applied 

directly against the tyres. To engage, press both brake levers 

forward against the stops. To release the locks, pull the levers back 

to their original positions.
Braking power will decrease with:

• Worn tyre tread

• Tyre pressure that is too low

• Wet tyres

• Improperly adjusted wheel locks
The wheel locks have not been designed to be used as brakes for a 

moving wheelchair. The wheel locks should therefore never be 

used to brake a moving wheelchair. Always use the hand-rims for 

braking. Make sure that the gap between the tyres and wheel locks 

complies with given specifications. To readjust, loosen the screw 

and set the appropriate gap. Then re-tighten the screw (Fig. 6.0 + 

8.0).

 CAUTION!

After each adjustment of the rear wheels, check the wheel lock gap 

and re-adjust if necessary.

Fig. 6.0

Fig. 7.0

1

Options - Footplates

Footplates:

The footplates can be flipped up to 

make it easier to transfer to/from the 

chair.

Lower leg length:

For users with longer legs, the leg 

support can be lowered to the 

appropriate level by using the 

screws (1). Loosen the screws, push 

the tubes to the desired position and 

then re-tighten the screws (see 

section on torque). There must 

always be a minimum gap of 25mm 

between the footplates and the ground, (Fig. 8.0).

Footrests and Latch

The legrests can be swung inwards 

under the seat sling or outwards. 

When fitting the legrests, the 

footrests must be pointing inwards 

or outwards. Then rotate the legrest 

inwards, until it locks into place. To 

remove, pull the lever (1), swing the 

footplate inwards or outwards and 

then lift the legrest out. Make sure 

that the legrest is locked into place 

correctly, (Fig. 9.0).

 CAUTION!

• 

The legrests must not be used to lift or to carry the wheelchair. 

• 

When getting on or off the wheelchair, do not use the footboards. 

These should be flipped up beforehand or the footrest should be 

swung to the outside as far as possible.

Fig. 9.0

1

Fig. 8.0

1

Содержание Breezy Style

























Отзывы: