Step 1
: Remove the device from previous zigbee network if it has already been added to
,
otherwise
pairing
will
fail
.
Please
refer
to
the
part
"
Factory
Reset Manually
".
Step 2
: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 4
: LED indicator will blink 5 times and then
stay solid on, then the device will appear in your
controller's menu and can be controlled through
controller or hub interface.
8. Factory Reset Manually
Step 2
: LED indicator will blink 3 times to indicate successful reset.
Step 1
: Short press “Prog.” key for 5 times continuously or re-power
on the DALI bus power supply 5 times continuously if the “Prog.” key
is not accessible.
Note: 1) If the device is already at factory default setting, there is no indication when factory reset again .
2) All configuration parameters will be reset after the device is reset or removed from the network.
DALI bus
AC Power
50/60Hz
Zigbee
Remote
< 10cm
6. TouchLink
to
a
Zigbee
Remote
Step 2:
Bring
the
remote or touch
panel
within
10cm
of
the
lighting
device
.
Step 3
: Set the remote or touch
panel into Touchlink
commissioning,
please refer to corresponding
remote or touch panel manual to
learn how
.
Step 4
: There shall be indication on the remote for successful link and
LED indicator will flash twice.
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3) For Hue Bridge & Amazon Echo Plus, add remote and device to network first then TouchLink.
4) After TouchLink, the device can be controlled by the linked remotes.
7. Removed from a Zigbee Network through Coordinator or Hub Interface
From your ZigBee controller or hub
interface, choose to delete or reset the
lighting device as instructed. The
connected light blinks 3 times to indicate
successful reset.
DALI bus
L
N
DALI BUS PS
DA DA
DALI bus
AC Power
50/60Hz
L
N
DALI BUS PS
DA DA
AC Power
50/60Hz
L
N
DALI BUS PS
DA DA
+A1
DA
DALI OUTPUT
DA
ZigBee to DALI Controller
Prog.
A1-A2: 8-230V
-A2
IMP
Add.
Group
x1
x10
5
0
1
6
2
7
4
9
3
8
5
0
1
6
2
7
4
9
3
8
+A1
DA
DALI OUTPUT
DA
ZigBee to DALI Controller
Prog.
A1-A2: 8-230V
-A2
IMP
Add.
Group
x1
x10
5
0
1
6
2
7
4
9
3
8
5
0
1
6
2
7
4
9
3
8
+A1
DA
DALI OUTPUT
DA
ZigBee to DALI Controller
Prog.
A1-A2: 8-230V
-A2
IMP
Add.
Group
x1
x10
5
0
1
6
2
7
4
9
3
8
5
0
1
6
2
7
4
9
3
8
5. Zigbee Network Pairing through Coordinator or Hub
(
Added
to
a
Zigbee
Network
)
Step 3
: power on the DALI bus power
supply, the device will be set into
network pairing mode (LED indicator
flashes twice slowly), the network
pairing mode will last until the device
is added to a zigbee network.
Step 1: Method 1
: Short press “Prog” button (or re-power on the DALI bus power supply) 4 times to start
Touchlink commissioning immediately, 180S timeout, repeat the operation.
Method 2
: If the device is already added to a network, it will be set into Touchlink commissioning immediately,
180S timeout. Once timeout, re-power on the DALI bus power supply to set it into touchlink commissioning
again.
