SUNLOVER HEATING
WARRANTY – SL6 DELUXE
This product is covered by a limited 3 year warranty against component failure or faulty
workmanship from the date of installation.
A faulty unit should be returned in the first instance to the dealer from which the unit
was purchased.
Damage to the unit due to misuse, power surges, lightning strikes or installation that is
not in accordance with the manufacturer’s instruction may void the warranty.
Warranty does not cover travel costs to or from installation site. Unit must be returned
to manufacturer for repairs.
If the power cord is damaged, do not use the controller; return the unit to the supplier
for repair.
Customer Record
. (To be retained by the customer);
Dealer/Installer Name
___________________________
Serial Number
___________________________
Date Installed
___________________________
For service assistance phone SUNLOVER HEATING
VIC
03 9887 2131
NSW
02 9838 0000
QLD
07 5597 7360
Factory 6
62 Parkhurst Drive,
7-9 Activity Crescent,
Knoxfield 3153
Molendinar 4214
Victoria Australia
Queensland Australia
Unit 2
20-22 Foundry Road,
Seven Hills 2147
NSW Australia
www.sunloverheating.com.au
MODEL SL6RR Radio Remote Solar Controller
With Time Clock
OPERATING INSTRUCTIONS
Summer Mode
is normal operating mode used during the Pool Swimming Season. You may set the
desired pool limit by pressing the UP or Down Buttons. The display shows the pool temperature then
flashes the limit setting and light, the pump light and pump will be on when solar gain is available.
Manual Mode
is used to prime, clean or test the pump. To select manual mode press the SELECT
button until the PUMP/MAN light is illuminated. The pump will then start, or stop if it has been running.
To return to normal run simply press the SELECT button till the AUTO light is illuminated. The SL6RR
will automatically return to AUTO run after 30 minutes, with a limit of 30 degrees.
Winter Mode
should be selected when the pool is not being used for extended periods. The pump will
be turned on for 3 minutes every day at the same time Winter Mode was selected. This will assist in the
systems off-season maintenance and save energy. To enter this mode press the SELECT button till the
WINTER light is illuminated. If the power is interrupted during winter mode the SL6RR will continue to
count time accurately. The batteries in the transmitter may be removed if desired at this stage.
Tropical Mode
is used to assist in cooling over heated pools. If the limit has been reached, which is
indicated by the limit light on, and the roof temperature drops below the limit temperature (usually
sometime late at night) the pump will turn on and pump pool water to the roof to cool it down. The
pump will turn off when the pool water is cooled to the limit setting. To set this function press the
SELECT button till the TROP light is illuminated. To switch back to Summer Mode press the SELECT
button till the AUTO light is illuminated.
Roof Temperature
When selected, the roof temperature will be displayed constantly for 3 minutes then return to AUTO.
The ROOF indicator will give 4 quick flashes when a signal is received from the transmitter.
Transmitter / Battery Low
When the SL6RR validates a received transmission, a flash from the Transmitter / Battery Low indicator
will be seen. If the Transmitter / Battery Low indicator is on steady the batteries in the transmitter must
be replaced before the unit will operate correctly in AUTO mode.
OPERATION
The SL6RR will turn the pump on when the roof temperature is higher than the pool (pipe) temperature
by 8°C and off at 4°C. Roof temperature is received every seven minutes from the transmitter. When
the pool temperature reaches the limit setting the limit light will flash, it will remain in this state while
the roof is hot to prevent over heating the pool. The SL6RR will then wait till 8:00 AM the next day to
start the process again. This function is to minimise the pool from overheating, hence reducing water
evaporation and consumption of chemicals. An auto flush program is incorporated to ensure accurate
pool temperature readings are obtained as the pool sensor is normally located well away from the
actual swimming pool and may sit in direct sunlight or in warm enclosures, the last recorded pool
temperature will be displayed for 6 hours from when the pump was last running. When auto flush is in
wait mode the limit light will be on constant until the pump is turned on for a three minute test, the
pump light will flash until this test is over.
