Sunker ELITE ONE Скачать руководство пользователя страница 5

 

 

 

 

- 8 -

 

OPERATION 

                                                                                                                                                                                                                                                                                                                                                                                                                         

A                                                                             

 

 

 

 

 

 

7. 

RX LED:

 The red LED indicates the unit is in the transmit mode. The green LED indicates 

the unit is in the receive mode.

 

 

8. 

CHANNEL DISPLAY:

 The channel display indicates the current selected channel

 

 

 
 
 

 

 

 

- 9 -

 

OPERATION 

                                                                                                                                                                                                                                                                                                                                                                                                                         

A                                                                             

 

 

REAR PANEL 

 

 

1. 

EXT. SP:

 This jack accepts 4 to 8 ohms, 5 watts external speaker. When the external 

speaker is connected to this jack, the built-in speaker will be disabled. 

 

2. 

DC POWER:

 This accepts 13.8V DC power cable with built-in fuse. The power cord 

provided with the radio has a black and red wire. The black goes to negative and red goes 
to positive.  

 

3. 

ANTENNA:

 This jack accepts 50 ohms coaxial cable with a PL-259 type plug 

 

Содержание ELITE ONE











Отзывы: